Dear Spuluka,
i tried all of this but result is same.
this is my srx log
-------------------------
loader>
U-Boot 1.1.6-JNPR-1.9 (Build time: May 17 2010 - 06:30:31)
SRX_650 board revision major:0, minor:11, serial #: AAEW1937
OCTEON CN5650-SCP pass 2.1, Core clock: 700 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 2048 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 8 MB
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Clearing DRAM........ done
Fuse: 0x0fff, Coremask: 0x0fff
BIST check passed.
0:00:00.0 Vendor/Device ID = 0x850910b5
0:01:01.0 Vendor/Device ID = 0x850910b5
0:02:00.0 Vendor/Device ID = 0xb68014e4
Boot Media: usb internal-compact-flash external-compact-flash
Net: octeth0, octeth1, octeth2, octeth3
ide 0: Model: CF 2GB Firm: 20080112 Ser#: 2012B 0000165041
Type: Removable Hard Disk
Capacity: 2000.7 MB = 1.9 GB (4097520 x 512)
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (244680 bytes)
Loading .rodata @ 0x8f03bc40 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f2b4 (16432 bytes)
Loading set_Xcommand_set @ 0x8f0432e4 (100 bytes)
Loading .rodata.cst4 @ 0x8f043348 (20 bytes)
Loading .data @ 0x8f044000 (5608 bytes)
Loading .data.rel.ro @ 0x8f0455e8 (120 bytes)
Loading .data.rel @ 0x8f045660 (136 bytes)
Clearing .bss @ 0x8f0456e8 (11656 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.9
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.9
(builder@zigeth.juniper.net, Mon May 17 05:45:58 UTC 2010)
Memory: 2048MB
[7]Booting from internal-compact-flash slice 3
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
Error on read (no IRQ) dev 0 blk 2584513: status 0x51
Error on read (no IRQ) dev 0 blk 2584513: status 0x51
Error on read (no IRQ) dev 0 blk 2584513: status 0x51
Error on read (no IRQ) dev 0 blk 2584513: status 0x51
can't load '/kernel'
Error on read (no IRQ) dev 0 blk 2584513: status 0x51
can't load '/kernel.old'
Press Enter to stop auto bootsequencing and to enter loader prompt.
Type '?' for a list of commands, 'help' for more detailed help.
loader> install file:///junos-srxsme-12.3X48-D70.3-domestic.tgz
/kernel data=0xb9e924+0x13c950 syms=[0x4+0x91d20+0x4+0xd6145]
Kernel entry at 0x801000c0 ...
init regular console
Primary ICache: Sets 64 Size 128 Asso 4
Primary DCache: Sets 1 Size 128 Asso 64
Secondary DCache: Sets 2048 Size 128 Asso 8
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
kld_map_v: 0x8ff80000, kld_map_p: 0x0
Copyright (c) 1996-2018, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 12.3X48-D70.3 #0: 2018-05-17 09:31:28 UTC
builder@kuzuryu.juniper.net:/volume/build/junos/12.3/service/12.3X48-D70.3/obj-octeon/junos/bsd/kernels/JSRXNLE/kernel
JUNOS 12.3X48-D70.3 #0: 2018-05-17 09:31:28 UTC
builder@kuzuryu.juniper.net:/volume/build/junos/12.3/service/12.3X48-D70.3/obj-octeon/junos/bsd/kernels/JSRXNLE/kernel
real memory = 2147483648 (2048MB)
avail memory = 922796032 (880MB)
FreeBSD/SMP: Multiprocessor System Detected: 12 CPUs
Security policy loaded: Junos MAC/veriexec (mac_veriexec)
Security policy loaded: JUNOS MAC/pcap (mac_pcap)
Security policy loaded: JUNOS MAC/runasnonroot (mac_runasnonroot)
MAC/veriexec fingerprint module loaded: SHA256
MAC/veriexec fingerprint module loaded: SHA1
netisr_init: !debug_mpsafenet, forcing maxthreads from 12 to 1
cpu0 on motherboard
: CAVIUM's OCTEON 56XX CPU Rev. 0.9 with no FPU implemented
L1 Cache: I size 32kb(128 line), D size 8kb(128 line), sixty four way.
L2 Cache: Size 2048kb, 8 way
obio0 on motherboard
uart0: <Octeon-16550 channel 0> on obio0
uart0: console (9600,n,8,1)
twsi0 on obio0
dwc0: <Synopsis DWC OTG Controller Driver> on obio0
usb0: <USB Bus for DWC OTG Controller> on dwc0
usb0: USB revision 2.0
uhub0: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
uhub1: vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 2
uhub1: single transaction translator
uhub1: 4 ports with 4 removable, self powered
umass0: JetFlash Mass Storage Device, rev 2.00/11.00, addr 3
pcib0: <Cavium on-chip PCIe HOST bridge> on obio0
Disabling Octeon big bar support
PCIe: Waiting for port 0 to finish reset
PCIe: Port 0 link active, 4 lanes
PCIe: Waiting for port 1 to finish reset
PCIe: Port 1 link active, 4 lanes
pcib0: Initialized controller
pci0: <PCI bus> on pcib0
pcib2: <PCI-PCI bridge> irq 0 at device 0.0 on pci0
pci1: <PCI bus> on pcib2
pcib3: <PCI-PCI bridge> irq 0 at device 1.0 on pci1
pci2: <PCI bus> on pcib3
pci2: <network, ethernet> at device 0.0 (no driver attached)
pcib4: <PCI-PCI bridge> irq 0 at device 2.0 on pci1
pci3: <PCI bus> on pcib4
atapci0: <SiI 3132 SATA300 controller> mem 0x100000-0x10007f,0x104000-0x107fff irq 0 at device 0.0 on pci3
unknown: Allocating IRQ for intpin 1, device atapci failed, i2cid
pcib0: Allocating IRQ for atapci failed
atapci0: unable to map interrupt
device_attach: atapci0 attach returned 6
pcib5: <PCI-PCI bridge> irq 0 at device 3.0 on pci1
pci4: <PCI bus> on pcib5
pcib6: <PCI-PCI bridge> mem 0x200000-0x21ffff irq 0 at device 0.0 on pci4
pci5: <PCI bus> on pcib6
pcib7: <PCI-PCI bridge> irq 0 at device 1.0 on pci5
pci6: <PCI bus> on pcib7
pcib8: <PCI-PCI bridge> irq 0 at device 2.0 on pci5
pci7: <PCI bus> on pcib8
pcib9: <PCI-PCI bridge> irq 0 at device 3.0 on pci5
pci8: <PCI bus> on pcib9
pcib10: <PCI-PCI bridge> irq 0 at device 4.0 on pci5
pci9: <PCI bus> on pcib10
pcib11: <PCI-PCI bridge> irq 0 at device 5.0 on pci5
pci10: <PCI bus> on pcib11
pcib12: <PCI-PCI bridge> irq 0 at device 6.0 on pci5
pci11: <PCI bus> on pcib12
pcib13: <PCI-PCI bridge> irq 0 at device 7.0 on pci5
pci12: <PCI bus> on pcib13
pcib14: <PCI-PCI bridge> irq 0 at device 4.0 on pci1
pci13: <PCI bus> on pcib14
pcib1: <Cavium on-chip PCIe HOST bridge> on obio0
pci14: <PCI bus> on pcib1
pci14: <processor> at device 0.0 (no driver attached)
CF error busy
CF timeout busy
CF error busy
CompactFlash model CF 2GB
ata0: <Octeon Compact Flash Driver> on obio0
gblmem0 on obio0
octpkt0: <Octeon RGMII> on obio0
cfi0: <AMD/Fujitsu - 8MB> on obio0
Timecounter "mips" frequency 700000000 Hz quality 0
###PCB Group initialized for udppcbgroup
###PCB Group initialized for tcppcbgroup
md0: Preloaded image </isofs-install-srxsme> 16795648 bytes at 0x80f430e4
WARNING: Expected rawoffset 2584512, found 63
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <JetFlash Transcend 2GB 1100> Removable Direct Access SCSI-4 device
da0: 40.000MB/s transfers
da0: 1920MB (3932160 512 byte sectors: 255H 63S/T 244C)
Trying to mount root from cd9660:/dev/md0
WARNING: preposterous time in file system
Kernel thread "wkupdaemon" (pid 47) exited prematurely.
WARNING: clock 11297 days greater than file system time
tty: not found
Starting JUNOS installation:
Source Package: disk0:/junos-srxsme-12.3X48-D70.3-domestic.tgz
Target Media : internal
Product : srx650
Computing slice and partition sizes for /dev/ad0 ...
Attempting to save existing configuration...
Could not find any existing configuration.
Formatting target media /dev/ad0 ...
Preparing to create slices on /dev/ad0
/dev/ad0: 4097520 sectors [C:4065 H:16 S:63 SS:512]
Shrinking sWARNING: Expected rawoffset 2584512, found 63
WARNING: Expected rawoffset 3968496, found 63
lice 1 by 64 blocks for alignment
Shrinking slice 2 by 32 blocks for alignment
Shrinking slice 3 by 464 blocks for alignment
1+0 records in
1+0 records out
512 bytes transferred in 0.000260 secs (1968363 bytes/sec)
Creating slices:
g c4065 h16 s63
p 1 0xA5 2048 1292224
p 2 0xA5 1294272 1292256
p 3 0xA5 2586528 1383984
p 4 0xA5 3970512 127008
a 1
******* Working on device /dev/ad0 *******
fdisk: /tmp/mbr: length must be a multiple of sector size
ERROR: Execution failed for command fdisk
Waiting (max 60 seconds) for system process `vnlru_mem' to stop...done
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...1 0 done
syncing disks... All buffers synced.
Uptime: 12s
Resetting all PIMs
Rebooting...
cpu_reset: Stopping other CPUs
U-Boot 1.1.6-JNPR-1.9 (Build time: May 17 2010 - 06:30:31)
SRX_650 board revision major:0, minor:11, serial #: AAEW1937
OCTEON CN5650-SCP pass 2.1, Core clock: 700 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM: 2048 MB
Starting Memory POST...
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash: 8 MB
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Clearing DRAM........ done
Fuse: 0x0fff, Coremask: 0x0fff
BIST check passed.
0:00:00.0 Vendor/Device ID = 0x850910b5
0:01:01.0 Vendor/Device ID = 0x850910b5
0:02:00.0 Vendor/Device ID = 0xb68014e4
Boot Media: usb internal-compact-flash external-compact-flash
Net: octeth0, octeth1, octeth2, octeth3
ide 0: Model: CF 2GB Firm: 20080112 Ser#: 2012B 0000165041
Type: Removable Hard Disk
Capacity: 2000.7 MB = 1.9 GB (4097520 x 512)
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (244680 bytes)
Loading .rodata @ 0x8f03bc40 (13940 bytes)
Loading .rodata.str1.4 @ 0x8f03f2b4 (16432 bytes)
Loading set_Xcommand_set @ 0x8f0432e4 (100 bytes)
Loading .rodata.cst4 @ 0x8f043348 (20 bytes)
Loading .data @ 0x8f044000 (5608 bytes)
Loading .data.rel.ro @ 0x8f0455e8 (120 bytes)
Loading .data.rel @ 0x8f045660 (136 bytes)
Clearing .bss @ 0x8f0456e8 (11656 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console
Found compatible API, ver. 1.9
FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.9
(builder@zigeth.juniper.net, Mon May 17 05:45:58 UTC 2010)
Memory: 2048MB
[8]Booting from usb slice 1
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
\
can't load '/kernel'
can't load '/kernel.old'
Press Enter to stop auto bootsequencing and to enter loader prompt.
Type '?' for a list of commands, 'help' for more detailed help.
loader>