Re: export network between routing instances
I think one of your other import terms then must be rejecing this route. I have the basic configuration working on a lab box. Configuration:root@none> show configuration routing-instances Trust-vr...
View ArticleSRX config for Playstation
Ok so my PlayStation is getting a nat type 3 and its affecting some online gaming. I configured my srx to all allow the ports the PlayStation has released. Here is my config, can anyone see whats...
View ArticleSRX Stateless UDP mode
Is there any possible way to let srx not create session for UDP traffic ?
View ArticleClik here to view.
Re: SRX Stateless UDP mode
Hello, You can bypass Flow daemon for UDP traffic using the below KB article with the help of Firewall filters. https://kb.juniper.net/InfoCenter/index?page=content&id=KB26757 However please be...
View ArticleRe: SRX Stateless UDP mode
Thank you paul for the fast answer , we use SRX 3600 . And i think the article is not for 3k series
View ArticleClik here to view.
Re: SRX Stateless UDP mode
Hi, That's right The first KB article is not for SRX 3600 as it does not supoort seelctive traffic in packet mode since it is a High End SRX device. On High End SRX device you will have to convert...
View ArticleRe: SRX 340 OSPF Advertise entire /23 when only portions of the subnet...
Thanks, The example works for aggregation if I assign send-aggregate the to the global ospf setting but I can't seem to get it to be constrained on a single interface if I set it as a policy on a non...
View ArticleRe: SRX Stateless UDP mode
As the device in packet mode will work as a router (and not a firewall), delete the security feature configuration from the device. As far as i see this time it lost protection features ?
View Articledefault Mode of SRX
Hi, I found confusing explanation about mode of srx. The first link page explains default mode is route mode and second link page explains mix mode is default . which is the correct ? Please go...
View ArticleRe: SRX config for Playstation
Your Playstation problem might be related to UPnP feature.Juniper SRX does not have UPnP feature since SRX is an enterprise firewall/router. Try this out...
View ArticleRe: SRX300 series VLAN interface
This is still an issue in D50 and specifically the srx300 model, it is not fixed.
View ArticleRe: SRX config for Playstation
Thats the guide I followed, the only think i didnt do was all the ports that he opened. So im assuming that I should include all of those ports that he did?
View ArticleClik here to view.
Re: default Mode of SRX
Hi Shyam, Mix-mode is the default. If you check the first link itslef there is a "NOTE" stating "Note: In mixed mode, which is the default mode, you can configure an SRX Series device using both...
View ArticleRe: export network between routing instances
Can you check if there is any other import policy? If yes, we need to make sure the last term on that policy states "next-policy" instead of "reject". You may use below comman to check if there is any...
View ArticleRe: VPN tunnels monitoring
Dears, I have tried all the mentioned OIDs but nothing was working for our case. all the "show snmp mib walk < OIDs>" output are empty .It may be software version dependent or is there any...
View ArticleRe: VPN tunnels monitoring
Dears, I have tried all the mentioned OIDs but nothing was working for our case. all the "show snmp mib walk < OIDs>" output are empty .It may be software version dependent or is there any...
View ArticleClik here to view.
Re: SRX Stateless UDP mode
Hello, Yes, That is right if you turn the SRX 3600 in Packet mode it will turn into a router and will lose all of its protection features. Unfortunately on High End SRX devices (like your SRX 3600) it...
View ArticleComit error message
Hello everyone! Today I was going to enable some debugging stuff and then I found some config which seems uncommited. I did rollback 0 and issued the commands in order to enable these debug stuff, but...
View ArticleRe: ipsec vpn config on MX80 MIC card
Hi, Thanks aarseniev, I set that as you mentined, so I have: run show configuration services ... policy all-ca-level-l1 { mode main; version 1; proposals Feve3-TT_ike_proposal; local-certificate...
View ArticleRe: Comit error message
Hi vstrabello, Are you configuring it in private mode ? Can you share the output of the commit command with the error message ? If you are configuring it in Private Mode try logging out and log in...
View Article