Re: SRX and ESX Configuration Assistance For Newbie
Thank you again for the assistance, I have reviewed the instructions and drawn pictures and come up with mock commands for my setup. The only questions I have before I dig in are: Do you know of a way...
View ArticleRe: "verify-sig:" error when upgrading software on an srx650
format should not be an issue. can you try using different usb port?
View ArticleRe: SRX210 - Ricoh MFP doesn't get internet connection
Hi guys thanks alot for your input on this. @Dawid: I really appriciate your input / correction on/of our configuration as I already assumed that it isn't proper (at all)Finally I came to apply your...
View ArticleRe: SRX210 - Ricoh MFP doesn't get internet connection
1. are you able to ping gateway .125 from SRX?2. are you able to ping 4.2.2.2 from SRX3. can you see proper arp entries on srx "show arp"4. "show security flow session status" and make sure ipv4 is not...
View ArticleRe: SRX and ESX Configuration Assistance For Newbie
The default policy on the SRX is deny. So any traffic that you do NOT have a rule to permit between the zones will be denied by the firewall without any further need for configuration. Generally you...
View Articleenaling ssh service on loopback interface in srx1500
Hi all, i want to configure ssh service on my loopback interface in srx1500.i put this interface in trust zone and enabled services all and protocols all on this zones.and beside that i enabled...
View ArticleRe: enaling ssh service on loopback interface in srx1500
Hi, Please check if ssh is configured under system services.If not,set system services ssh
View ArticleRe: enaling ssh service on loopback interface in srx1500
yes bro ssh is configured but still it i cannot access it
View ArticleRe: enaling ssh service on loopback interface in srx1500
Hi, You also need to check if you have the security policy for the traffic allowed or not.As shailesh said you need to have the system services also enabled for the devise to respond for the SSH....
View ArticleRe: enaling ssh service on loopback interface in srx1500
yes bro security policy is configured as well .in which source any destination any and application any is enabled but still it doesn't respond ssh access .i am confused that what else is left...
View ArticleRe: enaling ssh service on loopback interface in srx1500
could any pls share a complete configuration on this scenario so that i may be able to get help ..... Thanks in advance to all contributors in this forum from my side Regards,, Asif Khan
View ArticleRe: enaling ssh service on loopback interface in srx1500
Is the loopback address reachable on the network you are connecting from? When you ping and trace route to the loopback address does it respond to ping and go the expected direction. For self traffic...
View ArticleClik here to view.
[JSRX210H] Deleting commands results it syntax error, expecting ';', [Enter],...
Hello. I have JSRX210H and recently I configured access from outside to my virtual machines, like this: edit security nat destination set pool dst-nat-pool-student-vm1-ssh address 172.16.254.155 port...
View ArticleRe: enaling ssh service on loopback interface in srx1500
it would be easier if you share your config
View ArticleRe: [JSRX210H] Deleting commands results it syntax error, expecting ';',...
you are trying to delete 4 parameters(policy name, sourec, destination addres and application) in one line. try the below#edit security policies from-zone untrust to-zone trust# del policy...
View ArticleUnable to SSH/HTTPS Secondary node on SRX 5800 Cluster
Hi Experts, I am facing the issue accesing secondary node in SRX 5800 cluster from management network.below is the config.. Set version 15.1X49-D60.7set groups node0 system host-name node0set groups...
View ArticleRe: Unable to SSH/HTTPS Secondary node on SRX 5800 Cluster
HTTP/HTTPS to secondary node is not supported - ref https://kb.juniper.net/KB16827Regarding SSH, can you try adding a specific /32 back-up route for the source from where you are trying to do SSH,set...
View ArticleRe: Unable to SSH/HTTPS Secondary node on SRX 5800 Cluster
HTTP/HTTPS to secondary node is not supported - ref https://kb.juniper.net/KB16827Regarding SSH, can you try adding a specific /32 back-up route for the source from where you are trying to do SSH,set...
View ArticleRe: enaling ssh service on loopback interface in srx1500
Hi Asif, Please also check if you have any firewall filter configured on the SRX to protect the RE and it has the SSH allowed from the subnet that you are initiating traffic from. Suggest you to share...
View Article