Re: SRX100H2 Factory Reset Help Required
yes.performed nand format and reinstall, zeroize, and reconfigure via CLI. when I reboot-the old config comes back. cannot access JWEB or enable it no matter what I try. can only access management via...
View ArticleSRX real lab with ability to ping from win10 machine
hey, was looking to set up a real lab with routers and switches where i could ping from a windows 10 machine and also use wireshark to learning purposes. i was thinking about buying a 4 port PCIe card...
View ArticleRe: What the main reason when have "error bad UDP checksum" ?
Thats one possible reason. Can you try making the the MTU same on MX and SRX ?
View ArticleRe: GRE over Policy-Based IPsec Problem
GRE over IPSec is explained on https://kb.juniper.net/KB19372 GRE over IPsec has a few limitations in Junos (flow mode):IPSec tunnel needs to be route based.GRE end point and ipsec end point cannot be...
View ArticleRe: I have a problem with ip-monitoring and rpm in fail-over route default
You may be hitting https://prsearch.juniper.net/InfoCenter/index?page=prcontent&id=PR1192668https://prsearch.juniper.net/InfoCenter/index?page=prcontent&id=PR1263078
View ArticleEvent option and change of config
HI everyone, I want SRX 100 to do this:If RPM for 10.10.10.1 fails, install static route 8.8.8.8/32 next hop 10.10.10.2 using EVENT -OPTION SET UP: SRX 10.10.10.6----SW-----10.10.10.1F1 R1...
View ArticleShow chassis routing-engine command
Hi everyone When we use the command show below, we see " USER" , what does USER mean below?user@host> show chassis routing-engineRouting Engine status: Temperature 38 degrees C / 100 degrees F CPU...
View ArticleRe: Show chassis routing-engine command
It is about the user processes i.e. RPD Check other details of the command here https://www.juniper.net/documentation/en_US/junos/topics/reference/command-summary/show-chassis-routing-engine.html...
View ArticleSRX Per-unit-scheduling
I am having a bit of trouble replicating some orginal cisco qos configuration. I am in routed mode on the SRX. In summary, I have a physical wan interface with multiple dot1q sub-interfaces which are...
View ArticleRe: SRX Per-unit-scheduling
I just noticed this : root@SRX-300-TESTING# set class-of-service interfaces ge-0/0/5 unit ?Possible completions:<interface_unit_number> Logical unit number (0..1073741823) * Wild card, all...
View ArticleRe: Event option and change of config
I think you should have sevices ip-monitoring instead of event options: set services ip-monitoring policy PING-A-1 match rpm-probe Probe-Payment-Serverset services ip-monitoring policy PING-A-1 then...
View ArticlePossible to prioritise BGP keepalive messages ?
By default, SRX sends as best-effort. Is it possible to set the prority to Network control ? I have a qos policy on the outbound, I assume keepalive messages will be subject to this ? Thanks
View ArticleRe: Possible to prioritise BGP keepalive messages ?
You may try using “set class-of-service host-outbound-traffic forwarding-class...
View ArticleClik here to view.
Multiple site to site vpns
Hi All, Please forgive my newbness, i will most likely be outsourcing this unless i can get on some training but i'm after some confirmation. I need to link 5 facilities together. i was initially...
View ArticleRe: Show chassis routing-engine command
Hi, CPU utilizationInformation about the Routing Engine's CPU utilization:User—Percentage of CPU time being used by user processes.Background—Percentage of CPU time being used by background...
View ArticleDoes entire session will re-establish back if we change MTU on physical...
Hi all, i have some question and it contridict with what JTAC said to me. Below is the log that appear when i commit the change. During the commit all the session that login (application) has been kick...
View ArticleRe: Does entire session will re-establish back if we change MTU on physical...
What commands were used to change the MTU? This suggests the family inet address was deleted on the interface which would likely affect sessions. deletion of address on IFL reth8 has resulted in the...
View ArticleRe: Multiple site to site vpns
The SRX can handle this as either IPSEC or carrier ethernet. The use of IPSEC does limit the bandwidth capacity of the platform to cover the encryption overhead. So the SRX320 would be fine for the...
View ArticleRe: Does entire session will re-establish back if we change MTU on physical...
Hi spuluka, i'm using command "set interface reth8 mtu 9192" Thanks
View ArticleIs there any hidden command that can verify both cluster synchronize the the...
Hi all, Let's say previously i have setup the chassis cluster. But due to certain issue the Node1 need to be power off almost 3 weeks. So all the updated config on Node0. So when i join back the node 1...
View Article