Quantcast
Channel: All SRX Services Gateway posts
Browsing all 17645 articles
Browse latest View live

Re: SRX100 meltdown...

Hello , From CLI can you paste the outputs of : > show chassis routing-engine> show security monitor performance spu> show security monitor performance sess>show system processes...

View Article


Re: tacacs help

Hi every body, I have trouble with Tacac server.I could authen by Tacac successfully but the authorization is not successfull when i tested. I want deny the command "set interface xxx" but i still do...

View Article


Routing-Problem on SRX240

Hi, I have a strange behavior on our SRX240.We have setup several Site-toSite-VPNs (policy-based) and we are using the dynamic VPN (only with Pulse-Client).The Tunnels work fine. The Problem is, that...

View Article

Re: Is an SPC card failure graceful?

Hey, thanks for replying, I saw they were cold-swappable only, but does that mean if one (of several) in the chassis fails, the entire platform stops, do you know?

View Article

Image may be NSFW.
Clik here to view.

Re: vSRX IPv4/IPv6 - Example needed

This is exactly what i was looking for - thank you very much

View Article


Re: Is an SPC card failure graceful?

As far as I know, the Platform will continue to run but in order to replace the Card you would need to shut down the Platform anyways, which would result in downtime.

View Article

Re: Is an SPC card failure graceful?

Thanks Chris, That's just what I needd to know, understood we'll have to shut down the device to replace the card, but at least we'll be able to schedule that at a low traffic time and let it limp on...

View Article

Re: SRX 650 traffic selector limitation

I have similar issues. Did you find a reason for this? Would be nice with local/remote network and an config option "fully-mesh" instead of ~30 TS. //Rob

View Article


Re: SRX Cluster without using fxp0

Hello Guys I have a cluster of 2 srx650 10.2R310 and fpx0 disabled: groups { node0 { interfaces { fxp0 { disable; unit 0 { family inet { address 172.20.112.172/24; } } } } } node1 { interfaces { fxp0 {...

View Article


[HELP] need help to setup VLAN tagging

So basically i have an HP server that comes with iLO dedicated port, but i only have 1 network port to use so i want to be able to use that 1 network port to use as in/out network traffic and also iLO...

View Article

Re: SRX1400 - SRX1K-SYSIO-XGE - Interfaces won't come up/"device not...

Posting a follow up since I finally figured this out and got it resolved. So when we first got this SRX in, my techs hooked it up without an NPC/SPC. Not realizing the NPC was necessary to configure/go...

View Article

Re: [HELP] need help to setup VLAN tagging

Hello , You can try to use VLAN tagging : **/ Set interface for vlan tagging /**set interfaces ge-0/0/10 vlan-tagging **/set the unit number and assign a vlan tag. Typically you match the unit number...

View Article

Re: [HELP] need help to setup VLAN tagging

Hi Joses,    Can you post the code itself instead of the commands(like i post mine below)?This is because i use the cli editor so its much better than entering commands  This is what i have now...

View Article


Re: [HELP] need help to setup VLAN tagging

ge-0/0/10 { unit 0 { family ethernet-switching { port-mode trunk; vlan { members [ vlan2 ]; } native-vlan-id 1; } } }

View Article

Re: SRx in cluster send error: remote lock-configuration failed on node1

Hi I had a similear issue but I resolved it by connecting to the secondary node and do a rollback of the configuration. I belive it's a better way of solving it than commit synchronize force. In my...

View Article


host-outbound-traffic by interface

Hi all,My current Internet connection to ISP is a VLAN trunk link including two VLANs. My SRX need to get IP addresses from these two VLANs with DHCP. ISP requires all traffic in one VLAN must have...

View Article

Re: [HELP] need help to setup VLAN tagging

@smicker You are the best; literally!!!It worked great just like i wanted it. Unlimited thanks for taking your time to help; very much appreciated.

View Article


Junos Space cannot discover SRX chassis cluster using SNMPv3?

Hi All, Below is the minimum configuration SNMPv3 on my SRX. As i know on Junos Space or NMS the info that "bold" as per below need to match right between SRX and NMS. But the problem now Juos Space...

View Article

Re: SRX Cluster without using fxp0

Hi All,  Is is this command below will make service impact if i enable on production network. Currently my junos space just can view the master (node0) physical info only such as chasiss serial no and...

View Article

Re: SRX Cluster without using fxp0

My fxp0 ports do show up up when I do a show int terse even though they are set to disabled.

View Article
Browsing all 17645 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>