LAB SRX 540 To MX-140 IPSEC Tunnel
1.1.1.1--------MX---------xe-2/0/0----------------------------------------------XE-2/0/0--SRX-----2.2.2.2 10.0.1.1/30...
View ArticleLAB SRX 540 To MX-140 IPSEC Tunnel
1.1.1.1--------MX---------xe-2/0/0----------------------------------------------XE-2/0/0--SRX-----2.2.2.2 10.0.1.1/30...
View ArticleRe: LAB SRX 540 To MX-140 IPSEC Tunnel
root@SRX-TEST-540> show log kmd | last [Apr 11 19:46:04 PIC 0/0/1 KMD1]ikev2_fb_v1_encr_id_to_v2_id: Unknown IKE encryption identifier -1[Apr 11 19:46:04 PIC 0/0/1...
View ArticleRe: LAB SRX 540 To MX-140 IPSEC Tunnel
This is phase 1 proposal mismatchOne think I noticed you using on SRXset security ike gateway ike-gw local-identity inet 10.0.1.2 set security ike gateway ike-gw remote-identity inet 10.0.1.1 Remove...
View ArticleRe: LAB SRX 540 To MX-140 IPSEC Tunnel
The change in the SRX brought the IKE Phase 1 up, root@SRX-TEST-540> show security ike security-associations Index State Initiator cookie Responder cookie Mode Remote Address 71082059 UP...
View ArticleRe: LAB SRX 540 To MX-140 IPSEC Tunnel
You need to change one more thing :Current SRX config:set interfaces st0 unit 0Change to:set interfaces st0.0 family inet RegardsLeon SmirnovPlease Mark My Solution Accepted if it Helped, Kudos are...
View ArticleRe: Ip Monitoring not working with NAT
The configuration below is working as expected. The failover is fully functional without unplug and replug any connector.The only thing is that i don't want a specific route for in this case...
View ArticleDynamic VPN landing page on public IP.
HiOur SRX320 is showing the following landing page on our public IP "The SRX no longer provides hosting of the Pulse Client for direct download.Please obtain the Pulse Client from the Pulse Website"...
View ArticleHigh CPU on a SRX 100B
Hi everyone! I have a very special problem on a SRX100B. Around the same time every day the CPU spikes and when I check the services I can see that eventd and rtlogd is around 30% each. This goes on...
View ArticleRe: VPN Configuration on SRX1500 issue
Hi, As I am getting no luck with the NCP side of things, we have decided to utilise a slightly different approach as we already have Anyconnect working in a live environment. We have placed an ASA in...
View ArticleRe: VPN Configuration on SRX1500 issue
I will close this as resolved as I have the routing working and connectivity to all devices through the VPN. Thanks
View ArticleRe: LAB SRX 540 To MX-140 IPSEC Tunnel
Working Config: root@SRX-TEST-540> show configuration | display set set version 15.1X49-D50.3set system host-name SRX-TEST-540set system root-authentication encrypted-password...
View Articlehow to block https://www.123.com/abc
I want to block https://www.123.com/abc in SRXhow to achieve thispls give me a deatiled setup steps.thanks in advance
View ArticleSRX320 VPN authentication with Yubikey?
I'd like to start using a Yubikey for authentication for VPN sessions. What is considered to be the most straightforward way to do that with the SRX series? Thanks.
View ArticleSRX110H2-VA VDSL PIC Firmware
Hi Karan, I am trying to update my VDSL PIC Firmware. Can you please provide a link to the firmware file: jfirmware-srxsme-12.3X48-D65.1.tgz My system version and firmware are as follows:...
View Article1 Way LDP between SRX210/Cisco 2901
Working on a MPLS SP lab. It appears I am unable to establish 2 way ldp session between my SRX and Cisco 2811. My SRX shows an ldp neighbor, but my 2811 does not. Output below. Not sure if my egress...
View ArticleRe: SRX110H2-VA VDSL PIC Firmware
the srx110 downloads are here. https://www.juniper.net/support/downloads/?p=srx110 you will need to login to the support site for the downloads. if you don't have an account create one.If you get the...
View ArticleRe: Dynamic VPN landing page on public IP.
If you are not using the SSL vpn feature then simiply remove the public iterface from the web management configuration. delete the interface undersystem > services > web mgmt
View ArticleRe: Alarm set: License color=YELLOW, class=CHASSIS, reason=1 Logical System...
try running a commit full during an maintenance window to fully apply the current configuration.
View Article