Re: office365
MS are testing a new Web Service...https://techcommunity.microsoft.com/t5/Office-365-Blog/Announcing-Office-365-endpoint-categories-and-Office-365-IP/ba-p/177638- any chance of SRX or Junos Space...
View ArticleClik here to view.
SRX PROXY-ARP
Hope to get solution I have given ISP block xx.70.190.30/30 with 128 Public IP in different subnet on the gateway of primary ISP subnet xx.70.190.29.when i tried to map public IP to internal server...
View ArticleNAT policy for IP and PORT
Hi guys, in the following source NAT policy what does it means "destination-port 25"? it means"destination port 25 both UDP and TCP protocols"? and if yes, what about if I want to apply the NAT policy...
View ArticleRe: SRX PROXY-ARP
I'm not 100% sure I understand your question. You provided a /25 (128 addresses) on top of a /30 for client peering? The /30 interface would not use proxy-arp, in this case, you would just route the...
View ArticleSRX220H2 - Cluster Issues (secondary node flapping): High CPU JSRPD
I have a branch office with a cluster of SRX220H2s that recently started exhibiting flapping issues with the secondary node in the cluster. Every 5-10 minutes, the secondary node will be kicked out of...
View ArticleRe: NAT policy for IP and PORT
Hi,Yes, you are right. You can use "protocol" option to match tcp traffic or udp traffic or some other protocol.set security nat source rule-set nat_set_333 rule CICCIO_rule_13 match protocol tcp
View ArticleRe: SRX220H2 - Cluster Issues (secondary node flapping): High CPU JSRPD
Hi, Please provide the output of the below mentioned command:show chassis cluster information detail Is node0 CPU normal after disabling node1 interfaces from the Switch?
View ArticleRe: SRX PROXY-ARP
Thanks Mr. Jonathan I did 0.0.0.0/0 with a static route via /30 interface and /25 Network with a static route as well to /30 interface.when i apply static nat with out proxy-arp of /25 network, till...
View ArticleSrx240 boot loop after uboot
I have a problem with a srx240, bootloopingI have included a image of the loop
View ArticleSrx240 boot loop after uboot
I have a problem with a srx240, bootloopingI have included a image of the loop
View ArticleRe: Srx240 boot loop after uboot
Hi Joseph I believe its due to middle of upgrade or improper power down cause loader file to corrupt,you need to upgrade the loader file and U-boot via TFTP.
View ArticleVDSL layer 2
Dear Juniper lovers, I am currenlty searching for a solution to provide layer2 connectvity over vdsl. Our provider doesn't deliver a pure layer2 link. We need to use PPPoe to setup a link to our...
View ArticleRe: Has trouble with failover on SRX650-cluster
Hi! Does anyone have any ideas? My other two SRX-clusters does not have the same problems. I'm inclined to think that this is a hardware problem. But I do not know how to diagnose it....
View ArticleRe: The easy way / method to apply this policy?
Hi Spuluka, So it means need manually to insert policy to the top for every zone-to-zone policy. Is it any script that we can use in just one single click? Thanks
View ArticleRe: The easy way / method to apply this policy?
I am not aware of an existing script for this but if you had a lot of these to do this would be a good candidate for scripting out the solution.
View ArticleRe: ISP link failover from SRX firewall to SRX router
I was assuming you would source nat the traffic going out the iterface towards the mpls links. This would resolve the return path assymetrical routing issue. The idea is treat it as if it were...
View ArticleRe: Srx240 boot loop after uboot
cant seem to get into any command mode to input tftp address
View ArticleRe: Srx240 boot loop after uboot
Do you get a prompt where you an interupt the loop before it repeats?If so what prompt are you at? Do you have another SRX240 you can use to create a bootable usb for recovery?You can insert a usb and...
View Article