Juniper srx-100-b doesn't boot
Hi all I have a juniper srx-100-b and I tried to configure this device completely from scratch. I performed a 'erase all' command in u-boot mode, now the device doesn't boot. I don't see any post...
View ArticleMapping a /28 without NAT
I'm trying to set up an SRX240 to sit in between some servers and the internet where I can set the external IP on the servers themselves.I'm thinking NAT to internal addresses would be better but we...
View ArticleRe: Mapping a /28 without NAT
Hi ! No, you cannot route the same network from one interface to the other But on branch SRX ( lile the 240) you can do the following setup connect the external network to a Layer 2 interface in...
View ArticleRe: Strange IPsec behaviour between SRXs
Hello Hisham, The clients in the /77 network is connected to physical port fe-0/0/7, but the ports fe-0/0/1 to fe-0/0/7 are combined to a vlan1.Here is the config:security-zone TRUST { interfaces {...
View ArticleRe: Mapping a /28 without NAT
Thanks! I had suspected as much but had got tied in knots when I had split the network and it hadn't worked ... this turned out to be an issue with ARP sometimes not working but fixed with with the...
View ArticleCannot login to SRX100
Hello, I just used the wizard to setup my brand new SRX100. Using the web wizard I set my root password to: g$SY~THD=^8xK)/Q [yes, that is the actual password] After reboot, I cannot login using that...
View ArticleRe: Cannot login to SRX100
Hello Chris, There are few things you may like to check :- 1. Was it a plain text password?2. As per my understanding ")" symbol may not be supported in the password field. Check this out....
View ArticleRe: Cannot login to SRX100
Hi chrisstankevitz, The = character is not supported . Please type your password this way : g$SY~THD^8xK)/Q I just tested this out on my SRX210HE lab device .
View Articleempty proxy-identity for SRX
Hello,this is not a new topic but I still have some doubts about the proxy-identity setting for an SRX VPN : According to URL :...
View ArticleRe: Cannot login to SRX100
And just to be clear , my answer is regarding the wizard . I haven't tested the CLI mode .HTH
View ArticleRe: Cannot login to SRX100
Thank you both for your replies. Juniper: please don't accept "invalid" passwords and silently change them. Instead tell the user that the password is not valid. Please contact me directly for more UI...
View ArticleClik here to view.
Acceptable IKE pre shared keys
Hello, I just learned that JUNOS will change the passwords you specify without warning, for example if your password includes the symbol '=' (see this thread for more info). Question: Does JUNOS also...
View ArticleSRX 210 in transparent mode - trying to get inline management going
Hello, My work has a need for a layer2 firewall that can slip inbetween some vendor equipment that we're not to tamper/reconfigure and the uplink. Hence, transparent mode. Downside is I'm not sure what...
View ArticleJuniper to Cisco OSPF over IPsec
Hello, Does anyone know if its possible to setup an IPsec tunnel between a juniper and cisco and pass OSPF over it? Thanks
View ArticleSetting up Virtual Routers on an SRX 240
I admit I have no experience with Juniper devices prior to being tasked with setting up an SRX 240 for a test lab. I've followed documentation I could find, but can't quite get everything to work. I...
View ArticleRe: Juniper srx-100-b doesn't boot
If you are saying there is no output at all on the console port when you boot up. You have probably destroyed the flash files needed for boot with those commands. The correct way to reset the device...
View ArticleRe: Juniper srx-100-b doesn't boot
thank you for your reply. but is there a way to install the needed files on the flash? So yes, what files do I need and how can I install these files?Because I don't be able to get into u-boot mode...
View ArticleRe: Juniper to Cisco OSPF over IPsec
Hello,Yes - with OSPF-over-GRE-inside-IPSec.Possibly - with OSPF-inside-IPSec if You use NBMA network type and define neighbors statically - I haven't tested this personally.HTHThxAlex
View ArticleDynamic VPN Client Logging - SRX100H
Goodmorning Everyone, I am wondering if the SRX100 has the ability to log VPN connections for troubleshooting. This is my first Juniper product I've had to manage in a production environment and just...
View ArticleRe: Acceptable IKE pre shared keys
Hello,Not a direct answer to Your question but in JUNOS CLI You can enter IKE pre-shared key as HEX if You are not happy with supported ASCII subset being not up to Your requirements: --- JUNOS...
View Article