Re: How long should an upload and install take
Thanks. I am running into a problem even using CLI. The java application in the SRX is "Untrusted" by the latest version of Java running on my maching. I tried adding the SRX's IP to the trusted...
View ArticleRe: Traceroute between Virtual Routers not working (SRX200H)
I realize this is a three-year old thread, but here I am doing up what I hope is the first of many SRXes for CPE with management in a Virtual Router and I can't ping the **bleep** thing. I copied your...
View ArticleRe: How to add huge list of ips to prefix-list using CLI
Hi, Thanks. You can use 'load merge file.txt relative' to load config from a file or 'load merge relative terminal' to paste the lines of config directly onto the edit hierarchy. Both should work....
View ArticleClik here to view.
SRX 300 version downgrade to 12.3X48
Hello, I would like to downgrade my SRX 300 to version junos-srxsme-12.3X48-D30.7-domestic, because it has a longer support. See table below:ProductFRS DateEnd of EngineeringEnd of SupportJunos...
View ArticleRe: What list of service that need to reboot the SRX?
Hello , "Swapping the cards " i refered to changing faulty once due to RMA , since nothing in SRX are hot swappable . Now if you run cluster where one node have 5 SPC and other have 4 , it will not...
View ArticleRe: SRX 300 version downgrade to 12.3X48
Hello , SRX300 are NG devices which are supported from 15.1X49 version .
View ArticleRe: dhcpd service restart
Hello , When you change the lease time on SRX , it should be updated in next lease request seamlessly . But when you change the Gateway configuration , we may have to refersh the DHCP binding which...
View ArticleRe: SRX 300 version downgrade to 12.3X48
Hello , On SRX300 series and SRX1500 device we do not have downgrade options lower than 15.1X49 .
View ArticleRe: dhcpd service restart
Hi, So the lease time change by itself doesn't break connectivity. Thanks! Rubén.
View ArticleRe: Kernal Error in messages log
Yes,Every time I do a clear interface statistics all I get the same error messagesAny idea how to stop themDisclaimerThe information contained in this communication from the sender is confidential. It...
View ArticlevSRX maximum vpn tunnels
Hi, Is it possible to know how many VPN tunnels can be established on a Junos vSRX gateway ? The datasheet doesn't show anything and I can't find any command showing the limit of the vSRX. best...
View ArticleRe: Kernal Error in messages log
Hello , When you connected the PIM , have you rebooted the device ? If not can we try rebooting the box connecting the new PIM .
View ArticleRe: Kernal Error in messages log
Hello , Are you getting this logs on both Nodes or in specific node ? If you are getting in both Nodes , will it be possible to reboot them togethere ? If you are getting it in specific Node , try...
View ArticleRe: Kernal Error in messages log
Can you verify that the PIM is indeed the source of the messages by shut down, remove and startup? This does appear to be interface related, so the first step will be to verify which interface fpc/pim...
View ArticleRe: Kernal Error in messages log
Hi,I am not in a position to remove the Pim. We are also not using the management ports on the nodes.Could this be the cause?DisclaimerThe information contained in this communication from the sender is...
View ArticleRe: What list of service that need to reboot the SRX?
Hi Joses, When u said "since nothing in SRX are hot swappable" is it just refer to SPC & MPC & MIC only? Or it still include CB, RE and PSU? Let's say the faulty compoenent in chassis cluster...
View ArticleVPN fragmentation - How to check if SRX send fragments
Hi, I'm investigating a fragmentation issue for a VPN on a SRX running JunOS 12.1X46-D40.2.The remote host says that it's fragmented.I have set the: set security flow tcp-mss ipsec-vpn mss 1300Still...
View Article