vSRX 15.1 D50 cannot add ge- interfaces
Dear members; Has anyone succeded in adding ge-x/x/x interfaces to vSRX 15.....because it seems vSRX does not detect interfaces both in ESXi and KVM... Regards.
View Article802.1p and MPLS EXP CoS Rewrite on SRX300/SRX1500
Hi, All. Do either the SRX300 or SRX1500 devices support both 802.1p and EXP rewrite rules running on a core-facing interface? - asbestos-muffin
View ArticleRe: vSRX 15.1 D50 cannot add ge- interfaces
Hello, I have successfully added 7 NICs to my vSRX without any issues on ESXi.I have referred this link for the same....
View ArticleRe: 802.1p and MPLS EXP CoS Rewrite on SRX300/SRX1500
Hello, You can use below link to find out feature supportability....
View ArticleRe: IGMP Issue
Hi, @rtilak exactly, interface ge-0/0/0 is connected to the IPTV provider and vlan.21 is where the IPTV receivers are. A simple schematic is:<-------- Public Network...
View ArticleRe: 802.1p and MPLS EXP CoS Rewrite on SRX300/SRX1500
Hi Rushi, as Juniper has failed yet to add SRX300 and SRX1500 to feature explorer, it's pretty hard to say without actually testing it or have a local SE get the answer. Personally I would go for a...
View ArticleRe: Traffic shaping all egress traffic to ISP on SRX210 HA pair
Thank-you Suraj, I did come across that article but wasn't sure if that was the approach I was after. I will implement this evening.
View ArticleRe: 802.1p and MPLS EXP CoS Rewrite on SRX300/SRX1500
Hi, As per the datasheet, CoS including 802.1p and EXP is supported:QoS Features • Support for 802.1p, DiffServ code point (DSCP), EXP...
View ArticleRe: No ping Proxy-ARP from LAN/DMZ
Hello, Thank you for your answer.My config (partially) :interfaces { ge-0/0/0 { unit 0 { family inet { address XXX.XX.XX.90/29; } } } [...] } routing-options { static { route 0.0.0.0/0 next-hop...
View ArticleRe: SRX240 dual ISP
Hi Steve, Could you elaborate more with maybe a simple example. Would really appreciate Sam
View ArticleRe: SRX240 dual ISP
Hi Joses, How about in a case where you have 3 WAN interfaces; 2 for internet and one for VPN tunneling to branch offices. For the internet links, users are split between going through both links and...
View ArticleClik here to view.
Autoinstallation SRX 100
Hi, I need to configure many SRX 100h2 device at once. I'm thinking to use Autoinstallation. So i created a DHCP and TFTP Server. the dhcp is set to give to each SRX device an IP address. When i plug...
View ArticleNeed HELP! SRX cluster with BGP
HI All, I need some guidance. I have a client we are replacing a Palo Alto single unit with and SRX cluster. They also have dual ISP's. The ISP feeds are currently connected to their own Cisco...
View ArticleRe: Need HELP! SRX cluster with BGP
I also tried creating a trunk port and changing the Reth interfaces to L3 for ISP A and B trust side. I then have a seperate VLAN for each ISP with the ISP reth interfaces in it. But that still...
View ArticleRe: Autoinstallation SRX 100
I succeded to get this : root> show system autoinstallation status Autoinstallation status: Master state: Active Last committed file: None Configuration server of last committed file: None...
View ArticleRe: Need HELP! SRX cluster with BGP
Can you share a simple drawing of the setup and relevant configuration from the SRX? Will make it much easier to guide you. It sounds like the Cisco routers are handling failover between ISP A and ISP...
View ArticleRe: SRX240 dual ISP
Are your 3 WAN interfaces all on separate ISP? Basically, I would create a virtual router routing instance for each ISP with their own default route.routing-instance NAME type virtual router These...
View ArticleRe: SRX240 dual ISP
Unfortunately, internal network is flat. Certain IPs go through ISP 2 while the rest go through ISP 1. Seeing it's a Flat LAN, can I associate IPs to the VRs instead of interface?And since there's only...
View ArticleRe: 802.1p and MPLS EXP CoS Rewrite on SRX300/SRX1500
Hi, All. I have already read the datasheet and found about the supported features but I was looking specifically on having both 802.1p and MPLS EXP enabled as both rewrite rules on a core-facing...
View ArticleTraining / Troubleshooting: L2Circuit via Access Ports
Good Morning All! I am relatively new to Juniper. My company implemented them about a year ago and I've finally gotten around to working with them and I must say that I thoroughly enjoy the platform!...
View Article