Re: Cluster of SRX Firewalls in Two Data Centres
thanks alot , I 'll get back to you once i go through all.
View ArticleRe: Cluster of SRX Firewalls in Two Data Centres
HI, Another documentation that discusses this matter specifically:https://kb.juniper.net/library/CUSTOMERSERVICE/GLOBAL_JTAC/technotes/3500165-EN.pdf The cluster is set up accross Layer 2 and there...
View ArticleLACP on SRX 300
Does the SRX 300 support LACP? I seem to be reading conflicting reports online. When I try to configure LACP on the SRX300 I get the following error: [edit]root@.......# commit check[edit interfaces...
View ArticleRe: LACP on SRX 300
Hello, I would like to inform you that LACP is upport starting from version 15.1X49-D50.3 in switchin mode on SRX 300 and when I checked your configruation it is in switching mode and hence it should...
View ArticleRe: LACP on SRX 300
Hi, LACP is supported on SRX300 starting from D50 release. Regards,Sahil Sharma---------------------------------------------------Please mark my solution as accepted if it helped, Kudos are appreciated...
View ArticleThe problem with creating traffic shaping on srx 240 h2.
Hi. I have Juniper srx240h2. I want to create traffic shaping on untrust external interface ge-1/0/0 unit 75. On that interface i have 4 vlan's. I was creating filter, schedulers and scheduler-map....
View ArticleRe: Cluster of SRX Firewalls in Two Data Centres
Hi Pulkit, The document is great. Except that for layer2 connection we have same physical network (Whereas they have recommend separate connection for both Control & Fabric links. Other way i am...
View ArticleRe: Cluster of SRX Firewalls in Two Data Centres
Hi, Over the Internet connection, do you mean some layer 2 tunneling protocol over Internet?Please also note the requirement for latency:"latency shall not exceed more than 100ms between the two...
View ArticleRe: Cluster of SRX Firewalls in Two Data Centres
Hi Ash, Agreed that's not required. Actually that was said due to another config. Thanks
View ArticleRe: The problem with creating traffic shaping on srx 240 h2.
Hi, Applying a scheduler-map on a logical interface implies hierarchical CoS.You could apply the scheduler-map on the interface:class-of-service { interfaces { ge-1/0/0 { scheduler-map...
View ArticleRe: Cluster of SRX Firewalls in Two Data Centres
Hi Ash, Agreed that's not required. Actually that was said due to another config on these firewall also acting as G/w. Thanks
View ArticleSRX 300 can not enable loopback on physical interface
I am trying to enable loopback on physical interface. But it is not going up. I used : set interfaces ge-0/0/0 gigether-options loopback any idea? It used to work on srx-100H2
View ArticleRe: SRX 300 can not enable loopback on physical interface
Hi, I can observe the same in my lab.Which version are you using ?Please upgrade to D50 and then see if it workss. Regards,Sahil Sharma---------------------------------------------------Please mark my...
View ArticleSRX240H Anyway to Recover from dwc_otg_nandflash_bulk_flush+0x54 error?
My lab 240H rebooted for some reason and came up with the following error. From searching this forum it seems the flash died? It's out of support so I'm hoping there may be SOME way to recocover it?...
View ArticleRe: SRX240H Anyway to Recover from dwc_otg_nandflash_bulk_flush+0x54 error?
Hi, Please follwo the stepns mentione in the following KB to recover the SRX :-...
View ArticleRe: SRX240H Anyway to Recover from dwc_otg_nandflash_bulk_flush+0x54 error?
Performed, but failed: Press SPACE to abort autoboot in 1 seconds => setenv oct.net.init => saveenv Saving Environment to Flash... Un-Protected 1 sectors Erasing Flash... . done Erased 1 sectors...
View ArticleRe: SRX240H Anyway to Recover from dwc_otg_nandflash_bulk_flush+0x54 error?
Try reflashing the file system according to:http://www.juniper.net/techpubs/en_US/junos14.2/topics/task/installation/security-junos-os-tftp-srx-series-device-installing.htmlJust have a backup of the...
View ArticleRe: SRX240H Anyway to Recover from dwc_otg_nandflash_bulk_flush+0x54 error?
Attempted install: loader> install file:///junos-srxsme-12.1X46-D55.3-domestic.tgz /kernel data=0xb16d5c+0x134b2c syms=[0x4+0x8bbd0+0x4+0xcadc3] Kernel entry at 0x801000e0 ... init regular console...
View ArticleRoute problem from trust VLAN to external gateway
I have vlan.3 in my trust zone, and hosts in vlan.3 get an IP from the vlan.3 DHCP server just fine, and they can even ping the public IP I've assigned to the untrust interface on my SRX-210B. However,...
View ArticleRe: SRX240H Anyway to Recover from dwc_otg_nandflash_bulk_flush+0x54 error?
The SRX will boot from external USB first. So if you can create a snapshot to USB on a working SRX of the same model. Then insert that here you should be back in business.
View Article