Re: Configure SRX as NTP Server.
I have only ping, snmp, netconf on this interface.But NTP service is working fine
View ArticleRe: Site to site VPN routing problem
Hi, Sorry, this delay, other works. Yes, my mistake, I put wrong gateway,set routing-options static route 193.168.135.253/32 next-hop ""MAIN OFFICE""and then the traffic totally stop out. But, when I...
View ArticleRe: SRX1500 IPS failure
Make sure you have active licenses on both nodes "show system license"
View ArticleRe: SRX1500 IPS failure
Hi All, After some test it's look like due to time clock. After make correction of date and delete the db then it success. Thanks
View ArticleSRX1500 inline tape mode?
Hi All, Is there anyone here can tell me why the "set security forwarding-process application-services maximize-idp-sessions inline-tap" not available in SRX1500? I'm using junos version...
View ArticleRe: SRX1500 inline tape mode?
Inline Tap (only supported on High End Series SRX)This mode has the same separation of firewall and IDP process. However, the firewall process does not pass the traffic to the IDP process; instead it...
View ArticleRe: SRX1500 inline tape mode?
Please ignore the above post.https://www.juniper.net/documentation/en_US/junos15.1x49-d40/topics/reference/configuration-statement/security-edit-maximize-idp-sessions.html
View ArticleRe: SRX1500 inline tape mode?
Hi rsuraj, In SRX1500 the command / syntax "edit security forwarding-process" not available. Do u know whether it already change to other syntax or etc? Thanks and appreciate your guide
View ArticleRe: Vlan mapping
Hello Ashvin, It finally works using the device in bridge mode, i could make the translation of tags. The only problem is that maybe i will need in the same device to configure some ports in route...
View ArticleRe: SRX1500 inline tape mode?
HI kronicklez, the following hierarchy is also for High-End devices only. [edit security forwarding-process] Check supported platforms in the below link...
View ArticleSRX650 failed to boot
HelloWhen i try to upgrade boot loader i take following messges=> bootloader upgrade loader WARNING: Loader image with missing CRC header! Do you want to continue? [Y/N] (Default: N) y Un-Protected...
View ArticleRe: SRX650 failed to boot
Do you have another working SRX650? if so we can take a snapshot and boot this one.
View ArticleRe: SRX1500 inline tape mode?
Hi, SRX1500 is Data Center firewall and replacing of SRX1400. So it consider High End Firewall. Thanks and appreciate someone can check internally.
View ArticleRe: SRX1500 inline tape mode?
Hi Kronicklez,When I was chatting with some of the Juniper guys they mentioned that the 1500 firmware is based off the vSRX firmware which doesn't have the highend features. They were planning on...
View ArticlePKI - Error: Local Certificate doesn't exist
Hello forum guys, Recently installed MIC card for ipsec vpn services and tried to load certificate - ca loded sucessfully: admin@MX-80-1-Feve3-Rack-21# run request security pki generate-key-pair...
View ArticleVPN client unable to access 2nd site when connected to first site
I am fairly new to JunOS, I currently have 2 SRX240s configured with a Site to Site VPN tunnel. it all works fine. When i connect to one site via the dynamic VPN client (JunoPulse) i cant access the...
View ArticleSRX345 IDP config question/request.
Does anyone have a quick and dirty IDP configuration set command dump for an SRX3xx in tap/sniffer mode?
View ArticleRe: SRX1500 inline tape mode?
Hi Connor, Really? How our Juniper PS dont know about this? Even our Juniper SE still dont give any feedback. Too slow our Juniper PS and SE. Thanks
View ArticleVirtual Routers on Cluster Chasis
Hi everyone.I have a cluster chassis of Srx 650, i already have Reth interfaces, zones, static route and is already working. if config virtual routers will have impact to the flow of data?.Thank you.
View Article