Re: config IDP on SRX cluster failed
Hi Anand, I running JunOS 12.1, so can I using solution: copy IDP database file ?????? I has try re-download and re-install many time but not success, i also try command request security idp security...
View ArticleRe: From trust to trust zone for two internal network
It seems I had managed to set up the security and policy for 192.168.30.2/24 and 192.168.0.20/24 to access to each other. On the other hand, Server 192.168.30.2 connect to ge-0/0/2 is not able to...
View ArticleRe: Sub-interfaces on a SRX 240h
The show command didnt work gives me a syntex error, instead of set I used xml. Here is the output I was able to get, I have attached the file. If you need a different output just let me know.
View ArticleRe: Sub-interfaces on a SRX 240h
Hi tbuilt62, You have to run the command in configuration mode, the same mode from which you provided the original vlan configuration. That is why I put a '#' at the beginning of the command I gave you...
View ArticleRe: Sub-interfaces on a SRX 240h
Sorry about that, like I said I am a novice with the SRX. I have attached the output for the command you asked for.
View ArticleRe: Sub-interfaces on a SRX 240h
Hi tbuilt62, Not a problem ! It seems you are using the port I proposed you use and the only free ports are ports 14 and 15, this will be your new configuration : set vlans VehicleCompliance vlan-id...
View ArticleRe: Sub-interfaces on a SRX 240h
That will only take care of two new vlans, can those ports have sub-interfaces? I would like to create 11 more vlans.
View ArticleMACsec on SRX and in general
Hi, Aparently MACsec will now be supported on the new series SRX firewalls. Has anyone had experience on implimenting macsec on CCC or any supported platform. I am currious to know if it would work...
View ArticleRe: Sub-interfaces on a SRX 240h
Dear tbuilt62, Yes you can configure any port as a trunk and configure multiple vlans on the trunk ( with subinterfaces ) . From the configuration snippet you shared you already have a trunk...
View ArticleRe: Sub-interfaces on a SRX 240h
Sorry for all the questions. If I use the trunk port 13 and add subinterfaces, will I configure the interfaces like this?ge-0/0/13.1ge-0/0/13.2ge-0/0/13.3
View ArticleRe: Sub-interfaces on a SRX 240h
Dear tbuilt62, No juniper is different from Cisco. The interfaces you quoted are physical interfaces, the vlan subinterfaces are vlan.0, vlan.1, vlan.2 etc. We usually number the subinterface with the...
View ArticleRe: Sub-interfaces on a SRX 240h
Dear tbuilt62, If you are from a Cisco background this Juniper book will be good for you : http://www.juniper.net/us/en/training/jnbooks/day-one/fundamentals-series/junos-for-ios-engineers/ If you...
View ArticleRe: Sub-interfaces on a SRX 240h
Thank you for your time on this. I have made the changes you suggested can you look it over, let me know if this will work as you suggested?
View ArticleRe: Sub-interfaces on a SRX 240h
HI tbuilt62, Looks good except for one tiny piece. Execute the following commands to delete this : delete vlans VehicleCompliance interface ge-0/0/13delete vlans DeckNew interface ge-0/0/13 You only...
View ArticleSet Static Route with an Outgoing Interface
Hello, I have just purchased an SRX220 to replace my home router. I am trying to setup a static route but Virgin Media who are my ISP won't give me the Gateway IP address. On a Cisco device I know...
View ArticleRe: Set Static Route with an Outgoing Interface
Hi peter.arnett, The correct way to configure DHCP ( Client ) which is what you need is : ge-0/0/0 { unit 0 { family inet { dhcp-client; } }} For DHCP Client to work you also have to enable incoming...
View ArticleClik here to view.
architecture/config question
Hello, Trying to see if someone can assist with a traffic/architecture issue: I have several SRX's deployed which tunnel back to a central/hub ssg however under normal operations these remote firewalls...
View Article