IP-IP Tunnel .IPv6 to ipV4 Problem
Hi , some hours ago I set up IP-IP Tunnel on my firewall , but tonnel does not working .I can ping address on my side of the tunnel but i cant ping other side ...I'm Using Hurricane Electric Free IPv6...
View ArticleRe: SRX550 Firewill Filter Deletion/Timeout Issue via jWeb
So I am just trying to delete the two filters that have &. I tried to delete the filter and it keep giving me a syntax error. I have attached the #show firewall | display set logs, the #show...
View ArticleRe: RG0 was already failed over to node 0 after reset PEM from Node 1 for the...
I don't know if I understand you correctly but if you just want to switch RG0 and RG1 back to node 0 you have to do the following:For RG1request chassis cluster failover reset redundancy-group 1If...
View ArticleRe: SRX SIP packets doesnt flow, instead ICMP
Run a flow trace and see what is happening with the traffic. https://kb.juniper.net/InfoCenter/index?page=content&id=KB16110
View Articlere bios upgrade command is not valid on the srx320
Hi, New SRX320 - after upgrade to 15.1X49-D50.3 trying to upgrade re bios (like on srx2xx) > show system firmware Part Type Tag Current Available Status version version Routing Engine 0 RE BIOS 0...
View ArticleRe: SRX SIP packets doesnt flow, instead ICMP
It may be that SIP ALG needs to be turned off on your end and the ISP end. I've been able to get double NAT like your setup working with SIP, but if both devices are trying to do SIP ALG you may get...
View ArticleDefault-Route Doesn't show up in Forwarding-instance Routing Table.
I have a simple routing-instance config:GuestWifi { instance-type forwarding; routing-options { static { route 0.0.0.0/0 next-hop 7.91.187.65; But this default route doesn't show up in routing table:...
View ArticleRe: Default-Route Doesn't show up in Forwarding-instance Routing Table.
Hello, It is a strange thing.As long as you have interface-routes in the GuestWifi (imported from inet.0), default route should be visible.Do you have any filter to block the default route's import?Can...
View ArticleRe: re bios upgrade command is not valid on the srx320
Hello, Can you check if this works for you? https://kb.juniper.net/InfoCenter/index?page=content&id=KB27360&actp=search Regards, Rushi
View ArticleRe: Srx210 DHCP mac address block
Hello, You can try something like this: https://www.juniper.net/techpubs/en_US/junos11.1/topics/example/layer-2-vlans-firewall-filters-filtering-frames-by-mac-address-mx-solutions.html This will block...
View ArticleRe: IP-IP Tunnel .IPv6 to ipV4 Problem
Hello, Is there any specific requirement to use only ip-ip tunnel?Can you try IPSec tunnel or GRE? Regards, Rushi
View ArticleRe: re bios upgrade command is not valid on the srx320
Hello, I've checked and it is not working. The command bootupgrade do nothing. Here is output:root@NO2-130% ls -al /boot/ total 2996 drwxr-xr-x 4 root wheel 512 Dec 16 20:31 . drwxr-xr-x 12 root wheel...
View ArticleSRX240-SMB2-CS-3
Dear All, Do Juniper still provide this item:SRX240-SMB2-CS-3?I'm sure it still provide SRX240-SMB2-CS but not sure about SRX240-SMB2-CS-3. Thanks in advance. Regards.Muneer
View ArticleRe: IP-IP Tunnel .IPv6 to ipV4 Problem
Yes it should work. Maybe if you indicate which addresses are configured, that would help, insert some IP addresses so one oculd identify possibly a misconfiguration. The consruct looks ok, but at...
View ArticleRe: SRX 210 giving slow download speed but max upload speed
Hi chillipepper, May i know whether u have solution this issue. I have same issue. The diffrence is im using SRX1500 cluster and no VR involve in my setup. Appreciate if someone know the solution....
View ArticleRe: SRX240 Internet Speed slow
Hi All, I have the same issue on SRX1500 chassis cluster. Does some have the soution ? Thanks
View Articledhcp relay from a routing-instance
I have 2x srx5400 in active-passive cluster and the following topology DHCPClients ----(172.23.58.0/24) reth1.58 SRX reth1.590 (172.23.59.0/25)----(172.23.59.15) DHCPserver reth1.590 is in the...
View ArticleRe: Srx210 DHCP mac address block
By documentation Layer2 firewall filters are supported only on MX and EX platforms, Out of curiosity I've tried it on SRX110 12.1x47 in transparent mode and it didn't work. I was able to commit...
View ArticleRe: dhcp relay from a routing-instance
Hi vobelic, You may have to move to jdhcp.Please follow the below kb to achieve the same;https://kb.juniper.net/InfoCenter/index?page=content&id=KB26897&actp=search
View ArticleRe: dhcp relay from a routing-instance
i'm talking about dhcp RELAY, not dhcp server. And my configuration is actually the newer approach (previously, one had to use forwarding-options helpers bootp...)i.e. i'm only running dhcp-services...
View Article