Re: SIEM cannot received log when SRX using stream mode?
Hi sahilsha, Thanks for your feedback. I will ask the SIEM vendor to do packet capture on their side and keep update this issue to make sure in the future if anyone have same issue then they know the...
View ArticleClik here to view.
issue with static nat ip in ipsec vpn not reachable
Hello,I have ipsec tunnel configured on Juniper SRX240 on interface st0.2 with static nat to internal server of same ip range. VPN is up and i could ping interface ip from remote however natted ip is...
View ArticleRe: issue with static nat ip in ipsec vpn not reachable
Does the server and the entire return path from the server to the SRX have the route for 10.38.21.235? I assume you have a route out the tunnel on the SRX. But after it forwards the packet towards the...
View ArticleRe: Changing default LDAP port to 636
You can change the port from the access configuration for instance : set access profile profile1 ldap-server 10.10.10.30 port 5000
View ArticleGRE tunnel ping drop
Hi everyone, I have deployed GRE tunnels between Juniper routers MX104, with simple configuration, I am facing ping drop frequently, every 10 to 15 mintues time of span, from LAN to LAN and from Router...
View ArticleRe: GRE tunnel ping drop
Hello, What are the MTU settings on the Router interfaces?And what are MSS values configured on Firewalls? Regards, Rushi
View ArticleRe: GRE tunnel ping drop
Dear Rushi MTU settings on the Router interfaces is 1476MSS values on Firewalls flow tcp-mss 1350 -Saleem
View ArticleRe: traceoptions only showing dropped packets inspite of applying...
no i suppose.How does it relate to our traceoptions?
View ArticleRoot Password reset Juniper SRX100 (Defaulting the boxes)
Good day, I purchased two SRX100 devices on EBAY for pursuit of JNCIS-SEC cert. The devices however was not defaulted. I tried changing the root password by entering watchdog disable and the Loader...
View ArticleSRX340 High CPU temperature
Dear fellow Juniper-users, I recently replaced a SRX240HE2 with a SRX340, using the same configuration in the same environment.All works fine, I have no alarms, but I do see a rather high CPU...
View ArticleRe: Root Password reset Juniper SRX100 (Defaulting the boxes)
Hi, You can try to recover from an USB drive.Place the correct JunOS image on a FAT32 formatted USB drive.Create a junos-config.conf on this drive as well with the following content: (root password is...
View ArticleRe: Root Password reset Juniper SRX100 (Defaulting the boxes)
Hi, The procedure which pvandenbelt has suggested is explained in detail in the following link :- https://kb.juniper.net/InfoCenter/index?page=content&id=KB23882&actp=RSS Regards,Sahil...
View ArticleClik here to view.
Re: SRX340 High CPU temperature
Hi Folks,If you are replacing a SRX240 with a SRX340 in the same rack; i would suggest to double check the environment conditions. Since the air-flow pattern differs for both the boxes as below.Can you...
View ArticleRe: SRX340 Dynamic VPN
Hi degel3030, how you access the vpn? are you accessing the https://wanip/dyanmic-vpn or something?
View ArticleRe: SRX340 Dynamic VPN
After restart, i can access https://<wan ip>/dynamic-vpn. but the page said it doesn't offer pulse client to download. i did download the pulse client for my android mobile, what url should i...
View ArticleRe: SRX340 Dynamic VPN
I'm not sure if the mobile client works towards an SRX - but if it do, you just have to put in the IP address. No need for "https://" in front. You can download a client for Windows and Mac OS X here:...
View ArticleRe: Dual ISP Failover - RPM probe config issue
Hi, I have been same configured but I was unbale to revert back to primary line once it is up. have you any idea for this issue Thanks in advance Soph_Juniper wrote:Hello, In our test environment I...
View ArticleRe: SRX340 Dynamic VPN
finally, i did success using windows version pulse secure, it is just enter my wanip as the url. However, i still cannot connect using the adroid version pulse secure.
View ArticleRe: SRX340 Dynamic VPN
As stated, it wouldn't expect that to works as I only recon it as a SSL VPN client and currently the SRX only provides IPsec VPN-client connectivity. I know an ssl-based VPN client is planned for the...
View ArticleSRX 1500 Chassis Cluster meshing to F10
I have two new SRX 1500s that I've configured in a chassis cluster (using the 10-gig SFP xe-0/0/19 as fabric), which appears to be functioning, and which are going to replace two Cisco ASA 55xx series...
View Article