Link connection between two Virtual Router on SRX220
Hi all,My scenario is seperate SRX220 to two Virtual Router : Host 1 --> ge-0/0/1.0 ---SRX220--- ge-0/0/2.0 <-- Host 2From Host 1 traffic can reach to Host 2 and reverse. But with series...
View ArticleRe: SRX340 High CPU temperature
Hi Python, Thanks for your response.Actually both SRX'es weren't optimally placed, both the side-to-side cooled SRX240 and the front-to-back cooled SRX340 get their air from the warm side of the rack,...
View ArticleRe: Link connection between two Virtual Router on SRX220
Hi Ling NG You might find the below article useful: https://kb.juniper.net/InfoCenter/index?page=content&id=KB19787&actp=search Regards,Anand
View ArticleRe: SRX 1500 Chassis Cluster meshing to F10
Hi alexr92, The vlan config will look like this reth3 { vlan-tagging; redundant-ether-options { redundancy-group 3; } unit 182 { description "DMZ"; vlan-id 182; family inet { address 1.1.1.2/24; } }...
View ArticleRe: SRX340 High CPU temperature
Hi, not specifically a SRX340 but I have a SRX300 at home put inside a drawer together with an EX2200-C-12P-2G. CPU temperature on the SRX is just around 76-77C and has been running like this for more...
View ArticleRe: QOS on ST0 interfaces?
I was waiting for this feature and it is available from the new version 15.1x49-D70 onwards... CoS support for the st0 interface for SRX Series devices and vSRX instances—Starting with Junos OS...
View ArticleRe: Link connection between two Virtual Router on SRX220
You can use Physical link between VRs. Or import routes between routing...
View ArticleSRX removal from Cluster
Hello, I have a had a quick look and it appears it can be done with the command 'set chassis cluster disable reboot I take it this needs to be done individually on both nodes ? Would the interfaces go...
View ArticleRe: SRX removal from Cluster
You need to do this individually on both nodes. Regarding reth, you will have to remove the configuration and then configure normal Ethernet ports. Other config like security policies /zones can be...
View ArticleClik here to view.
Trouble with excecute netconf on a srx 1400
I have a jtac case on this, but just incase anyone have had the same problem.When we try to excecute commands on the device (we have accessed it with ssh blah@1.1.1.1 -s netconf), the srx closes the...
View ArticleRe: Link connection between two Virtual Router on SRX220
Thank Anand10, rsuraj, Can you give me some example use Physical link between VRs? What interface? Routing between VRs? The main purpose of scenario is: traffic from Host1-->sub-VR...
View ArticleRe: Link connection between two Virtual Router on SRX220
Hi Folks,I just tried the same in a MX box and please find the working config, +----------------------+ | LOOP Cable | |...
View ArticleClik here to view.
Re: L2TP through SRX
Ditto, i have a real issue with this... Want to move from pptp to l2tp... pptp is working fine but i cannot get l2tp to work no matter what i try
View ArticleSRX IDP Policy - No counters
Hello,I setup my SRX220 IDP for the 1st time today. I wonder why I don't see counters on traffic outbound? Do I also need to setup an inbound Policy? The Guest Network listed is an internal wifi...
View ArticleClik here to view.
Re: SRX IDP Policy - No counters
Think I got it. I re-ordered the Polices for the Guest Network putting iDP First. From zone: Guest, To zone: Internet Policy: idp-app-policy-1, State: enabled, Index: 12, Scope Policy: 0, Sequence...
View ArticleRe: Link connection between two Virtual Router on SRX220
The SRX220 does support logical tunnel interfaces. https://kb.juniper.net/InfoCenter/index?page=content&id=KB21260
View ArticleRe: L2TP through SRX
You can only do the l2tp pass through if the ip address is NOT on any SRX interface space. You need to setup the nat forwarding with an assigned address not used directly by the SRX.
View ArticleRe: Link connection between two Virtual Router on SRX220
ya, i know about that.So i have plan to use the physical interfaces for connecting a virtual router to the physical one. I've tried the idea of @python but it also not support SRX. Any other solution...
View ArticleRe: Link connection between two Virtual Router on SRX220
What exactly is not supported with SRX ? Can you share the session log with commit error seen during the configuration? I will try to help you with it. -Python
View ArticleRe: L2TP through SRX
Hi, I currently have it set up so i have another public ip proxy arp'd on the srx external interface, then i have a destination NAT rule to forward an traffic to my pptp server. This is working fine....
View Article