stupid question about ipv6
Why when I do show route IPv6:Addr::61gives me nothing. but if I do this: show route IPv6:Addr::61/64 I get some static routes?
View ArticleRe: Broadcast Vlan
Thanks for your Help!! Do you think that ip broadcasting direct can works between vlans??? Thanks. Regards.
View ArticleRe: Broadcast Vlan
I can't see any reason why it should not work but I've never configured it/ Why don't you test it out and see if it does what you need it to?
View ArticleHardware change VPN won't authenticate (certificate auth)
I have a remote site that is connected to another site via a site to site tunnel using pki / cert based auth. My new firewall has the same config, etc., but I had to generate a new cert since the old...
View ArticleSyntax error
I have written a config and checked it inside out. The SRX220 will not load the config with a "Syntax Error" but me and Notepad ++ cannot find it anywhere. Any clues?
View ArticleRe: Syntax error
snmp { community TCS-Read {view-jweb-view-all; authorization read-only; } }
View ArticleRe: Hardware change VPN won't authenticate (certificate auth)
Fixed - was an issue with the cert. The IP was being put in as DNS: in the ASN on the cert. It needed to be generated with the IP ad IP:. Seems obvious, but I didn't realize that the SRX was so...
View ArticleVpn created behind NAT device
There is a couple things I'm not getting. I found a doc that says to add: set security ike gateway ike-gateway1 local-identity hostname juniper.net; But I don't know what side to put it on. Or if it...
View ArticleRe: SRX Blocking Youtube in UTM-EWF
its been more than a year since this was posted. has juniper fixed this issue? our testing with the latest signatures still cannot block https://youtube. are we just missing something here?
View ArticleRe: Vpn created behind NAT device
Hello , In this case its pritty simple . I hope that you do not have any Dynamic IP assigned to FW1 or FW3 , only thing here is that FW1 is behind a NAT device . So FW1 will have all the normal...
View ArticleRe: Dynamic DNS on SRX with dyndns.org
Hello , Can you check if PP0.0 is assigned to a zone and host inbound services are enabled ?
View ArticleRe: DNS-Name Wildcard Entry
Does anyone know if this capability has been added to the SRX yet?
View ArticlevSRX VPN IPSec Site-to-Site PPPoE problem
Hello ladies & gets, I am new in Juniper and generally JunOS but I found it easier to learn, so in order to make my first steps with the real deal -SRX- I got firstly vSRX in order to test some...
View ArticleRe: Broadcast Vlan
Do you think that ip broadcasting direct can works between vlans???No. Broadcast traffic will only be visible within a broadcast domain. In general, the VLAN is the broadcast domain. Junos has...
View ArticleRe: DNS-Name Wildcard Entry
Not in address book entries. Wildcard entries can be used with web filtering.
View ArticleRe: vSRX VPN IPSec Site-to-Site PPPoE problem
Hello, Please find the answer to your queries in the above post as below:- 1. set interfaces ge-0/0/3 unit 0 family inet address 1.1.1.2/30 <--in r.s.* this interface is our default...
View ArticleRe: SRX Blocking Youtube in UTM-EWF
Hello, I would like to inform you that earlier the behaviour of UTM with HTTPS traffic/websites was not consistent becasue we used to send IP address for resolution and since the DNS IP of the HTTPS...
View ArticleSRX220 trouble with IPsec VPN
Hi,everyone.I have an SRX220 and we're trying to set up an IPsec VPN with SRX650. On SRX220 IPsec phase 1 failed: on "show security ike sa" - blank.All VPN related configuration such as encryption...
View ArticleRe: stupid question about ipv6
Hello, Please share the results for both the commands and also please share the configuration for static routes if possible. ThanksPulkit Bhandari
View Article