Clik here to view.
Re: SRX220 trouble with IPsec VPN
Hello, From the attached configruation it seems that you are using route based VPN tunnel on SRX. But in the above configuration I see that you have not binded the st0.0 interface with the VPN tunnel...
View ArticleRe: SRX220 trouble with IPsec VPN
many thanks!!! All problems are due to carelessness.)
View ArticleRe: DHCPv4 Server
Hello Guys, Any news about this problem?We have a similar problem. Maybe the same
View ArticleClik here to view.
Re: SRX DDNS with Google Domains
Hello, As per the documentation only two servers (www.dyndns.org and www.ddo.jp.) are right now available to be configured for DDNS settings on SRX as DDNS servers. Hence you would not be able to...
View ArticleSRX OSPF Single area
Hi,I just want to be verified whether my SRX OSPF configuration is correct or not.So far I can ping to each SRX interfacehttps://nbctcp.wordpress.com/2016/04/20/ospf-labs/ tq
View ArticleRe: SRX OSPF Single area
Looks like a correct basic configuration. Personally, I would only use RFC1918 addresses in a lab like this instead of routable ones on your links like 12.12.12.2/30. Labs should follow the published...
View Articlesrx - youtube performance - slow buffering
hi,I am using srx220h2 at home. srx is connected to router (from ISP) via 1gig link. On srx were configured: VRFs, NAT toward Internet, zones and sec for traffic. One host is conected via other 1gig...
View ArticleRe: srx - youtube performance - slow buffering
Hi, Try lowering the TCP-MSS on the SRX user@srx# set security flow tcp-mss all-tcp mss 1350
View ArticleClik here to view.
User in Internet activity statistics.
Our small and medium client often ask about small system to log "user in Internet" activity. We tested couple solution but none of them meet the expectations.What we need:- of course syslog based;- one...
View ArticleClik here to view.
Re: srx - youtube performance - slow buffering
Hello, Are you using any additional features on SRX like Antivirus, Web Filtering, IDP, etc. If Yes, Then please disable them and then check if it gives a positive impact. Thanks,Pulkit...
View ArticleSRX Cluster to Cisco switch stack config for resilience
Hello, Wondering if you could help. We have a situtation where we need to connect our SRX cluster to two cisco switches (which may or may not be stacked - still awaiting more information from the...
View ArticleSSG and SRX VPN Problem
hi all, I have a problem in phase2 when I trying SSG550M (screenos 6.2) as hub and srx100 (junos12.1) as spokes. The message is there was preexisting session from the same peer. Spokes (SRX100H2) are...
View ArticleRe: SRX Cluster to Cisco switch stack config for resilience
Assuming you have an Active/Passive SRX cluster, take a look at the Full Mesh Chassis Cluster starting on page 18 of the high availability guide. This shows EX switches but you can use Cisco as well....
View ArticleRe: SSG and SRX VPN Problem
I assume you have looked for notable differences between the two SRX100 configurations to see if anything is different. Some settings to verify in this situation: NAT traversal should be enabled since...
View ArticleRe: SRX Cluster without using fxp0
Hi with release 12.1X46-D35.1 this not happens @srx-re1> ...ps | match fxp0 | display set set groups node0 interfaces fxp0 disableset groups node1 interfaces fxp0 disable @srx-re1> show...
View ArticleISG to SRX Active/Active conversion
Hi all,I'm trying to convert from an ISG to an SRX however I'm having a problem. Active/Active on an ISG is done via virtual system whereas the SRX does it by port group. So to replicate it I'm trying...
View ArticleClik here to view.
Re: class of service does not work on vpls interface?
Hello, Could you please tell if the SRX is working in full packet based mode or selective packet bsed mode since you are using VPLS services on SRX which are available only in packet-mode (L2 mode)....
View ArticleSRX650 cannot configure LAG on build-in port
Hello, I have one SRX650 with only 4 build-in port. I want to bundle interface to connect to my core switch. But I can not create LAG ae0 from 2 build-in port: ge-0/0/2 and ge-0/0/3 and run LACP. I see...
View ArticleRe: SRX650 cannot configure LAG on build-in port
Its still the same. You may refer the latest release notes with this information on http://www.juniper.net/techpubs/en_US/junos12.3x48/topics/concept/layer-2-ethernet-port-switching-security-overview.html
View Article