Clarification of permit tunnel action
I am reading some VPN examples from the O'Reily Juniper SRX Series book. One thing I'm not clear on, and I've been unable to find additional information in the Junos documentation, is the full behavior...
View ArticleRe: Clarification of permit tunnel action
Hi Ecartner, On the SRX there are two types of tunnel route and policy based. Below is an example of the policy based vpn tunnel.Using the security policy below the policy-based vpn tunnel will be...
View ArticleClik here to view.
Re: Clarification of permit tunnel action
Hello, In Policy Based VPN tunnel the policy with the permit tunnel action serves the following purpose. Get the Proxy ID's for the negotiation of IKE Phase 2. (This is taken from the policy created...
View ArticleRe: Vpn created behind NAT device
Thank you for the response. That makes perfect sense. I've been out that past several days once I get caught up on some things I'll try that config out.
View ArticleRe: Broadcast Vlan
Hi spuluka,, Thanks for your reply. I understand you however Could you show me how can I do it?? I don´t find any command. I want that this broadcast only will be possible trough only one interface, If...
View ArticleRe: Broadcast Vlan
Hi, I have seen this one, bridge-domains { vlan100 { domain-type bridge; vlan-id 100; interface ge-2/2/1.100; interface ae1.100; } vlan200 { domain-type bridge; vlan-id 200; interface ge-2/2/1.200;...
View ArticleRe: Broadcast Vlan
The first confguration example is creating the bridge domains where all the members of the domain will be in the same broadcast domain. This is your desired configuration. But you really cannot...
View ArticleRe: Broadcast Vlan
Thanks for your respond. For example VLAN 1 has a network 192.168.0.0 255.255.255.0 and I want to send a broadcast paquet to 192.168.1.255 (VLAN 2). Do you think that broadcast ip direct is the...
View Articlecannot in mode configure on srx 3400
Hellow i have srx3400 chassis cluster and i want to add new configuration but i can't user mode configure. this error from node :warning: Clustering enabled; using private editUsers currently editing...
View ArticleRe: cannot in mode configure on srx 3400
please try the below from primary. root# commit synchronize force
View ArticleRe: Broadcast Vlan
Are you saying that you want the broadcast address of vlan 1 to be forwarded to vlan 2 in a different subnet and appear as the broadcast address of vlan 2 192.168.1.255?
View ArticleRe: Broadcast Vlan
Hi, If I have a host in Vlan1 and I have 2 hosts in Vlan2, I want send one packet from host 1 to the theses host by broadcast (it is a summary of the network). I don´t know if I explained right....
View ArticleRe: SSG and SRX VPN Problem
I check the different between 2 srx100, no differents. NAT is enable at ssg550 and SRX100 default enable NAT.Lfetime settings on phase 2 also match between the SSG550 and SRX100. Phase2 message on...
View ArticleRe: Broadcast Vlan
Moreover I have tryed the bridge domain Vlan Although I have not lucky. I think that this operation is only to Switchs becouse I have the next code interfaces { fe-0/0/0 { unit 0 { family inet { dhcp;...
View ArticleRe: SSG and SRX VPN Problem
I located a kb article on this message that seems to match your scenario. since you are already running 6.2 it looks like you should try setting the soft life timer on the SSG550the workaround for...
View ArticleRe: Broadcast Vlan
I'm still not sure I understand, but it is sounding like you are looking for non-standard packet handling behavior. A broadcast packet is generated by an application to a destination address that is...
View ArticleRe: Broadcast Vlan
Thanks for your respond, ok I understand your clarification, thank you very much. The issue is that I was looking for the bridge domain because you told me that I could introude 2 vlans in the same...
View ArticleRe: ISG to SRX Active/Active conversion
Hello, On ISG devices, you unet vsd 0. Create multiple VSDs in such a way that some are active of one node while other are active on another node. On SRX devices, when you create a reth interface, you...
View ArticleRe: Broadcast Vlan
There are two parts to how this packet handling works once the packet is on the network from your software. 1-the generated broadcast packet flooding to all your VLANsThe bridge domain solves this...
View Article