Re: Problems Completing PPPoE Auth SRX 110
Thank you very much for your suggestion but unforunetly it's not that easy. I've checked the username and psswd at least 20 times and in addition the username and psswd works fine on my opensource...
View ArticleRe: Problems Completing PPPoE Auth SRX 110
Hi, I doubt SRX doing anything abnormal; i don't think SRX is problem here. you can upgrade to 12.3 and check but your log capture clearly indicates Auth Req Tx (out) towards the ISP and the reply Rx...
View ArticleRe: Problems Completing PPPoE Auth SRX 110
HiIf you have other sessions running with same username/password, it could still be a problem on ISP end. Radius can be configured to allow only certain number of sessions and reject if it crosses the...
View ArticleRe: Problems Completing PPPoE Auth SRX 110
I agree the ISP needs to answer why I am receiving an "AUTH-NAK msg request denied" not "Access Reject" and I am not running side by side sessions but am testing one at a time. There is definitely...
View ArticleRe: Problems Completing PPPoE Auth SRX 110
I am happy to announce and a little proud I must say, (persistance pays off) that I fixed the issue.It seems that the **bleep** ISP was infact checking PADO tags.I upgraded to version 12.3 and enabled...
View ArticleIKEv1 : Error: TImeout
Dear All Suddenly site to site vpn not working, getting error message " IKEv1 Error: Timeout". I've check the ike service enable on untrust zone.I think IKE service is not working on firewall.Please...
View ArticleRe: Problems Completing PPPoE Auth SRX 110
Good to know that it’s fixed ☺️Sent from my iPhone
View ArticleRe: SRX220, SRX-MP-1VDSL2-A and VDSL Vectoring
HI, jfirmware package at download site is still work in progress (https://www.juniper.net/support/downloads/?p=junos-srx).Meanwhile, I'll repost jfirmware packages at ftp for your download.
View ArticleRe: Trying to create a vlan
went through all the commands line for line and it took all of them when i tried to commit the unit to the programming i got an error that said interface 0\0\1 in security zone i took it out and it...
View ArticleNAT - Static Source vs. Static Destination
Hi all,could you please confirm if there is any difference between configuring Static Destination or Static Source NAT?I understood they would end up doing the same thing?Are there any important...
View ArticleRe: SRX220, SRX-MP-1VDSL2-A and VDSL Vectoring
Hi Karan,Maybe you havnt uploaded the firmware yet, or it hasnt synchronised yet. I cant anything at ftp://ftp.juniper.net/pub/incoming/Is that the correct address?Thanks,
View ArticleRe: NAT - Static Source vs. Static Destination
Static NAT is Bidirectional, which means the initiating traffic can be in either direction and depending either source or destination will be translated.From the configuration point of view it is...
View ArticleDifference in monitor interface command between physical interface and reth
Hi guys i noticed that: xe-0/0/9 up upxe-0/0/9.0 up up aenet --> reth2.0........xe-4/0/9 up upxe-4/0/9.0 up up aenet...
View ArticleVPN Configuration on SRX1500 issue
Hi, Because we are configuring an SRX1500 for IPsec VPN we are using the NCP client. We have a situation where the client connects, but in a strange way (FQDN Username does not equal XAUTH username but...
View ArticleRe: Difference in monitor interface command between physical interface and reth
Monitor xe-0/0/9 indicates the input of that particular phy interface, whereas on reth2, I believe its combined cumulative input bytes from xe-0/0/9 & xe-4/0/9. The current delta [0] is cleared.
View Articlepacket mode in SRX higg end or bypass security policy
There is a firewall filter to forward traffic to a forwarding instance: term 2 { from { source-address { 1.1.1.1/32; } destination-address { 0.0.0.0/0; } protocol tcp; destination-port [ 80 443 ]; }...
View ArticleUser Identification with active directory on SRX and Routing-Instance
Hi I've some trouble configuring active-directory connection on one SRX.What about the other SRX without routing instance, same configuration NO problem.In this case with routing instance yes...I've...
View ArticleClik here to view.
Re: VPN Configuration on SRX1500 issue
So, I am now a little confused. I have set the st0.0 interface into the correct zone and also the correct VR (now where we are directly connected. If I monitor the interface traffic I see the IP Ping...
View Articlefailover or bgp vpn between SRX (Site A) to SRX & SSG5 (at same site with...
We have site-site vpn setup between srx (Site A) and ssg5 (Site B) , and now we have added one more srx router at Site B (with same Intranet but different ISP Internet ). Now i have to bring up one...
View Article