Re: Ospf between srx and mikrotik
Hi, Does it alway remains in "init" state? or does go up to "2-way" state or "exstart/exchange state" and falls back? If your OSPF is stuck & remains in "Init" state, that means you have...
View ArticleRe: Ospf between srx and mikrotik
Hi, There is known PR condition tracked PR #1274667, where OSPF over GRE over IPSec is not supported on SRX with standalone CP. This is a dayone issue in standalone CP and is fixed in JUNOS 17.3R1...
View ArticleRe: Ospf between srx and mikrotik
Hi, Current installed Srx 5400 version is 15.1X49-D120.3. Should i install latest version : 17.3R2 ?
View ArticleRe: Ospf between srx and mikrotik
Hi, Yes, fixed in 17.3R1 onwards so, 17.3R2 should be fine.
View ArticleClik here to view.
Re: Ospf between srx and mikrotik
Updated to 17.3R2 and ospf started working. Thanks for the help!
View ArticleRe: License needed for PPTP on SRX
Agree with JonesyComau here. The SRX cannot terminate a pptp vpn only ipsec or ssl vpn. You can pass through the SRX via policy and/or destination nat to a pptp server. And that will not require any...
View ArticleSRX to Two ISP failover configuration
Good evening We have the following setup: SRX HA Cluster 1500 Site A: HQ:SRX Node 0 ----> ISP 1---->MX-104 primary SRX Node 1 ---->...
View ArticleRe: SRX to Two ISP failover configuration
Hello, You can try using VPN monitoring or routing protocol over st interface.This way if VPN is down, corresponding st interface will be brought down. Regards, Rushi
View ArticleSRX1500 - PCAP equivalent
Hi, Is there an SRX1500 equivelant command for the SRX1400 command "edit security datapath-debug" please? Seems quite useful to get a direct PCAP output....
View ArticleRe: SRX to Two ISP failover configuration
Could you provide the full config output for each tunnel? I’ve helped design a solution for this in the past, so I know what you’re doing is possible.I also agree, in that you should run a routing...
View ArticleRe: SRX1500 - PCAP equivalent
Hi,Please refer the KB for collecting packet capture from srx1500:https://kb.juniper.net/InfoCenter/index?page=content&id=KB11709
View ArticleRe: PPPOE Not Working
It looks like it may be the access-concentrator line (access-concentrator srx300)This is the name of the access concentrator you are connected to, not your own device, try disabling this and try to...
View ArticleRe: SRX to Two ISP failover configuration
Nate, Yes i understand it will make sense to run a routing protocol. I am attaching the full config of the srx-1500. I was thinking on running two eBGP connections. The SRX-1500 will have two ebgp...
View ArticleSRX redundant Ethernet interface does not come up.
I configured a redundant Ethernet interface in an SRX1500 cluster using a 10 Gbps interface on both devices. I need to change this reth to use 1 Gbps interfaces; thus, I changed the configuration to...
View ArticleRe: SRX redundant Ethernet interface does not come up.
Can you please provide the following information. * running Junos version* chassis cluster configuration* output from 'show chassis cluster interfaces' ?* output from ' show configuration |display set...
View ArticleRe: SRX redundant Ethernet interface does not come up.
Thank you for your support. I returned to the original configuration using the 10 Gbps interfaces for reth0 and configured a new reth, reth4, that uses the 1 Gbps interfaces. I plan to rewrite the...
View ArticleCreating a simple trunk interface
Hello First time trying to create a trunk interface in srx router, did some googling and came up with config, but i think something is still missing since i cant ping the interface even from router...
View ArticleRe: HELP! SRX 5400 em0 up but em1 down
you shoukd have two control links in order for the em1 to come up. So you need two routing engnies
View ArticleRe: Creating a simple trunk interface
Hi,You defined l3interface as irb.203 in vlan config but forgot to define irb interface. Create irb interface and delete vlan interface.set interfaces irb unit 203 family inet address...
View Article