Quantcast
Channel: All SRX Services Gateway posts
Browsing all 17645 articles
Browse latest View live

Re: Creating a simple trunk interface

You problem is that SRX4100 and higher platforms doesn't support ethernet-switching. you should create a physical interface with vlan-tagged logical interfaces instead and refer to these in your...

View Article


Re: SRX redundant Ethernet interface does not come up.

Ok. Remember that you can quickly move all configuration to reth4 by doing a simple "replace pattern reth0 with reth4" in configure mode and then just revert to reth0 on the 10G port.

View Article


Image may be NSFW.
Clik here to view.

Re: Creating a simple trunk interface

Thanks for the info, works like a charm and cleaner code also.  Intresting that i didnt find such example in google...

View Article

Re: SRX 1400 - redirect blocked users to custom URL

Did you figure this out? I'm experincing the same issues. I can see that the firewall does either drop when set to deny or send a tcp reset when set to reject. But it doesn't redirect the user to the...

View Article

Re: SRX redundant Ethernet interface does not come up.

Thank you for your support.  The 'replace pattern' command is most useful.    

View Article


Routed Subnet

Hi guys, I was wondering if you can help me. I have 2 questions on routed subnets. 1. What is a routed subnet? 2. I have a SRX210 and I'm somewhat of a newbie to Juniper. I Just wanted to know how to...

View Article

Re: Routed Subnet

You can either create some routing-instances or you can use the default "trust" and "untrust".... Personally, I like to use my own configs rather than the defaults.... for me I would complete the...

View Article

Re: SRX redundant Ethernet interface does not come up.

FYI. I tried the 'replace pattern' command; the result is below. root@SRX1500-cluster# replace pattern reth0 with reth4error: target statement 'reth4' already exists[edit interfaces] 'reth0' could not...

View Article


Re: Routed Subnet

I popped together a quick config..... Hopefully not missed anything..... Will point you in the right direction though 1: Interface configuration: set interfaces (interface) unit 0 description (give it...

View Article


Re: Routed Subnet

Welcome to Junos. What you are describing is a standard service provider setup. Where we have the first subnet for the connected interface to the CE (client equipment). Then route the assigned client...

View Article

Re: SRX220, SRX-MP-1VDSL2-A and VDSL Vectoring

Hi,  I am also looking for jfirmware-srxsme-12.1X46-D67.tgz for my srx100. Is it possible to have this uploaded to the FTP? It's not currently downloadbale from the downloads page. Cheers

View Article

Re: SRX220, SRX-MP-1VDSL2-A and VDSL Vectoring

Renza7,12.1X46-D67 is still available on the main download site. https://support.juniper.net/support/downloads/ At the top select srx100Then change the version pull down to the 12.1x46D67 is available...

View Article

Re: SRX220, SRX-MP-1VDSL2-A and VDSL Vectoring

Thanks for your reply. I can download the junos release from that page, but not the corresponding jfirmware release. I am looking for the jfirmware to update my dsl PIM firmware. thanks edit: sorry...

View Article


Re: SRX220, SRX-MP-1VDSL2-A and VDSL Vectoring

Today is your lucky day.. get firmware from ftp:ftp://ftp.juniper.net/pub/incoming/   

View Article

Re: SRX220, SRX-MP-1VDSL2-A and VDSL Vectoring

Thanks for the link Karand,  but there doesn't appear to be any files available there to download

View Article


Re: SRX220, SRX-MP-1VDSL2-A and VDSL Vectoring

it takes a while for ftp to sync up..check after sometime..  

View Article

Negated Addresses

HiI'm confused about destination-address-excluded and source-address-excluded. I tyr to read an example following these link...

View Article


Re: Negated Addresses

Your example is correct, 10.10.10.0/24 will be denied as a source address but allowed as a destination address.20.20.20.0/24  will be denied as a destination address but allowed as a source address....

View Article

SRX340 HA Cluster Strange Behaviour on Reth Interface - Unknown Egress Traffic

Hi All,  I am having a strange issue on an SRX340 Cluster pair - with strange unknown traffic egressing out of a Reth interface that is configured as a trunk port on an ethernet switch - with a few...

View Article

Image may be NSFW.
Clik here to view.

Re: SRX340 HA Cluster Strange Behaviour on Reth Interface - Unknown Egress...

Have noticed very high byte counts on all interfaces  Am starting to think this may be a firmware bug.

View Article
Browsing all 17645 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>