Re: Logical System in SRX
Hello , 1) what are the physical requirments for logical-system in srx. do i need to have seprate physical interface for each logical system ?> You need to have licences to have user logical...
View ArticleRe: Mini PIM compatible for all SRX device? (SRX-MP-1VDSL2-R)
Hello http://www.juniper.net/techpubs/en_US/release-independent/junos/topics/reference/specifications/rj11-connector-pinouts-vdsl2-mpim.html...
View ArticleRe: Mini PIM compatible for all SRX device? (SRX-MP-1VDSL2-R)
That still does not answer the question. One of the links talks about the pin-out of the RJ11, the other an overview of the card.
View ArticleRe: Mini PIM compatible for all SRX device? (SRX-MP-1VDSL2-R)
Sorry, I noticed the supported platforms on the side. Thanks
View ArticleRe: Connectivity Between 2 SRX
Hi,Thanks for your response, i guess to configure VPN first we should have reachibility to gateways right and static route is not required as both devices are in same network but why i am not able to...
View ArticleRe: Connectivity Between 2 SRX
I apologise, I think I have misunderstood the issue. Are you saying the following?That SRX1 ge-0/0/0 1.1.1.1/30 is connected to SRX2 ge-0/0/0 1.1.1.2/30.SRX1 can not ping 1.1.1.2.If so then please...
View ArticleDHCP not working properly on juniper
DHCP is not working very well for my Juniper SRX or maybe someone needs to point me in the right direction dhcp { pool 10.10.0.0/16 { address-range low 10.10.1.1 high 10.10.255.254; maximum-lease-time...
View ArticleRe: Logical System in SRX
Thanks for the answers, so 1) what are the physical requirments for logical-system in srx. do i need to have seprate physical interface for each logical system ?> You need to have licences to have...
View ArticleRe: Logical System in SRX
Hello , >>> I got the neccessary license, if i go with logical interface for each logical-system then I ll be controling vlans. right ? which is not recommended.Ans ) Yes , for L3...
View ArticleClik here to view.
Re: DHCP not working properly on juniper
Hello, Please share the output of the command "show system services dhcp binding" when the static binding is configured and the lease for the previous DHCP allocation has not timed out but the clinet...
View ArticleRe: site to site vpn for policy-based issue
Hi, Could I set source NAT or Destination NAT? Enclosed the Site B config.
View Articleroute failover using ip-monitoring not working
Hi All, I have tried to configure route faiover using ip-monitoring,please see the configuraion below. set services rpm probe BSNL test BSNLTST target address 10.31.0.1set services rpm probe BSNL test...
View ArticleRe: DHCP not working properly on juniper
Hi Please try to do the below steps, Previously expired IP address is still bound to the MAC address of the clientTo ensure that the client is receiving the static address, as per it's MAC, run the...
View ArticleRe: site to site vpn for policy-based issue
I have had a look through and cannot see a problem with the config. The only thing is you do not need to put fe-0/0/0 thru fe-0/0/3 into a security zone as they a layer 2 interfaces and you have put...
View Articleaddress-assignment pool static options
Within a DHCP pool, i have two hosts that require a different boot-server than all of the other hosts. With the "old" method, it would be pretty simple: system { services { dhcp { pool 10.0.0.0/24 {...
View ArticleRe: DHCP not working properly on juniper
Here is the output root@srxrouter% cli root@srxrouter> show system services dhcp binding IP address Hardware address Type Lease expires at 10.10.1.8 00:16:3e:37:60:d6 dynamic 2016-05-27 20:52:05 EDT...
View ArticleRe: Connectivity Between 2 SRX
Hi, Please find the below output, i am also sharing whole conf. SRX1:root> show interfaces terseInterface Admin Link Proto Local Remotege-0/0/0 up upge-0/0/0.0 up up inet 1.1.1.1/30root# show...
View ArticleRe: SRX NAT internal routing issue side effect.
Sounds like the DNS doctoring ALG may be active on the device and updating records automatically. Try explicitly turning this off and test if the behaviour changes.set security alg dns disable
View ArticleRe: DHCP not working properly on juniper
Your problem stems from a false expectation of what a DHCP server should do. As jsree noted you should not assign a static address to a device if you've already configured a dhcp server to use it in a...
View ArticleDynamic VPN, Pulse Secure Error 1453
Hello, I've been strugging to set up dynamic vpn on my SRX220H2 for many weeks now. My Pulse Secure client is on a Windows 7 laptop. When I try to log in with Pulse Secure, it says "Connection...
View Article