Re: route failover using ip-monitoring not working
Hello , Here you do not need 2 probes and 2 policy . BSNL probe and BSNL policy will be enought to do rout failure . Please remove the RCOM prob and policy and check if the route failover happenes .
View ArticleRe: Dynamic VPN, Pulse Secure Error 1453
Hello , This issue looks similar to a know issue PR 1135780 - DVPN cannot connect due to fail to get HTTP Response This issue is fixed in version : 12.1X47-D35 12.3X48-D25 15.1X49-D30 Try upgrading to...
View ArticleRe: Replacing a SSG5 with SRX100H2 in branch office
Sorry about the PFS, you are correct I misread the proposal listings there. As far as the proxy-id are concerned, these are explicitly configured on the SSG140 side so would need to remain on the SRX...
View ArticleRe: DHCP not working properly on juniper
So a DHCP server does not check if an ip address is in use and not re-assign that ip but assign a different ip?Isn't that how dhcp works?
View Articlehelp with zones and D-NAT trying to learn more about these
In and effort to learn more about these SRX boxes, I got a used one for my house (along with a 24poe ex2200, I have a couple question that i have given the "5minute rule" but i cant figure out. 1. i...
View ArticleRe: route failover using ip-monitoring not working
so i need to do this for my home, where connection 1 is via 4gLTE with 20GB limit, then i want to connection 2 my "wifi as wan" router to another SRX port so when it connect to our phone with unlimited...
View ArticleRe: help with zones and D-NAT trying to learn more about these
Hello , PFA the respondses : I deleted my trust to trust zone deactived the " apply groups" and while traffic was blocked the log file did not show this, why is this not working? > When you...
View ArticleRe: route failover using ip-monitoring not working
Hello , Ideally one probe is enought for route failover between 2 ISPs . Since the primary link will be active all the time .
View ArticleClik here to view.
Re: DHCP not working properly on juniper
Hello, No, The DHCP does check if an IP address is in use or not and assign a different IP address if one is in use. But in your case the IP address was assigned dynamically to one machine with some...
View ArticleRe: DHCP not working properly on juniper
How do i clear the dhcp and lets it start all over? I don't want to exclude, i just want it to respect my static assignment So what command to clear? Thanks
View ArticleRe: DHCP not working properly on juniper
clear dhcp server binding link for more details:http://www.juniper.net/documentation/en_US/junos12.1x46/topics/reference/command-summary/clear-dhcp-server-binding-srx.html HTH
View ArticleRe: SRX cluster running two different versions of Junos. Easy fix?
I've upgraded node0 to the same version as node1, but I'm now stuck with a cluster redundancy status that is different on both units, and both nodes showing the other node in a "lost" state. Any...
View ArticleRe: DHCP not working properly on juniper
getting error that dhcp subsystem not running clear dhcp server binding all warning: dhcp-service subsystem not running - not needed by configuration. restart dhcp-service warning: dhcp-service...
View ArticleRe: help with zones and D-NAT trying to learn more about these
joses wrote:Hello , PFA the respondses : I deleted my trust to trust zone deactived the " apply groups" and while traffic was blocked the log file did not show this, why is this not working? >...
View ArticleRe: Is the zone vpn a must for Route-based VPN?
Thank you!! In my case, it's swap from ISG to SRX, and previous policies are all in Gp_untrust zone for operator's roaming. So if not mandantory to have vpn zone on my SRX, I will keep it the same...
View ArticleClik here to view.
Re: site to site vpn for policy-based issue
It's some missing setting for my mistake. Thanks for all your help!!!
View ArticleRe: SRX cluster running two different versions of Junos. Easy fix?
Hi milkman, From this output it seems like the control link is not exchanging probes.Can you check the output of the below command 2-3 times on each node;>show chassis cluster control-plane...
View ArticleRe: Replacing a SSG5 with SRX100H2 in branch office
Thanks Steve for your continued efforts! I have replicated much of the environment in a home lab with a SSG5 running the SSG140 config and the SRX100H2 trying to connect to the SSG. I have 2 Netscreen...
View ArticleRe: Connectivity Between 2 SRX
I can see nothing wrong wth your configuration. I assume that you have configrmed that SRX1 ge-0/0/0 is connected to SRX2 ge-0/0/0. Can you tell me which SRX device you are using?
View ArticleRe: help with zones and D-NAT trying to learn more about these
okay i figures out hte ports scan the TCP flood in the screen config was cuasing that
View Article