Clik here to view.
Re: address-assignment pool static options
Hello, First of all the old configuration is no longer supported on the newer versions and hence you should not use the system services dhcp heirarchy to configure the DHCP settings as it might just...
View ArticleClik here to view.
Re: DHCP not working properly on juniper
Hello, Please try using the command "clear system services dhcp binding <ip_address>" andd see if it works for you. Thanks,Pulkit Bhandari Please mark my response as Solution Accepted if it...
View ArticleClik here to view.
Re: Connectivity Between 2 SRX
Hello, Could you please check after disbaling the screen feature enabled for ge-0/0/0 interface on both the SRX. Please do so using the following commands on respective SRX:- deactivate security zone...
View ArticleRe: Replacing a SSG5 with SRX100H2 in branch office
I don't think the linked issue applies here because their problem seems to have been nat on the gateway address. Did you also remove the vpn monitor from the SRX config? I just noticed that was in...
View ArticleRe: Connectivity Between 2 SRX
I am testing in GNS3 using vsrx firefly, i will disable Screen feature and let you know the results. Thanks,Bharath
View ArticleRe: route failover using ip-monitoring not working
HiIn my case I want to use both connection at the same time.How to acheive that. RegardsSree
View ArticleRe: Replacing a SSG5 with SRX100H2 in branch office
Yep, i took VPN monitor off the SRX back in message 5 as that got me some SA's. I removed Establish immediately and seems the SSG5 still registering the preexisting peer message. config's attached. Thanks
View ArticleRe: Replacing a SSG5 with SRX100H2 in branch office
Hello. Looking at the config, there is potential mismatch in the local/remote ID sent between the firewalls during Phase1 negotiation. Can you try to add the following on the SRX? set security ike...
View ArticleRe: Replacing a SSG5 with SRX100H2 in branch office
SWEET! Tunnel is up! I added that remote identity Host name containing the SSG hostname. Now, do i need to add all these subnets to the VPN security zone to be able to reach all my other remote...
View ArticleRe: Replacing a SSG5 with SRX100H2 in branch office
Hello. Based on current configuration, yes, it's required to add the detination prefixes to the VPN zone address book. However, going forward, it's recommended to use 'global' address book,...
View ArticleRe: Connectivity Between 2 SRX
SRX2:root# deactivate security zones security-zone untrust screen[edit]root# commitcommit complete[edit]root# run ping 1.1.1.1PING 1.1.1.1 (1.1.1.1): 56 data bytes^^^C--- 1.1.1.1 ping statistics ---7...
View ArticleRe: Connectivity Between 2 SRX
Please could you tell me the SRX model you were using before you used vSRX? i.e. the SRXs you used in the original lab.
View ArticleRe: Connectivity Between 2 SRX
I have dumped your configs onto 2x SRX210s and it works fine. lab> show interfaces terse ge-0/0/0 Interface Admin Link Proto Local Remotege-0/0/0 up up ge-0/0/0.0 up up inet 1.1.1.1/30lab> ping...
View ArticleRe: Replacing a SSG5 with SRX100H2 in branch office
Ok thought the remote subnets would be simple, having an issue. So i added 172.16.182.0/24 to both VPN address book and to Trust zone and cannot reach it from a PC behind the 172.16.72.1 SRX. From the...
View ArticleClik here to view.
Re: Connectivity Between 2 SRX
Hello, Since youa are using vSRX on GNS3, please check if you are running into the same problem as in the following document:- https://gns3.com/discussions/unable-to-ping-between-two-junos Please let...
View ArticleRe: Denied Mac Address
Hi social, Please check the below link wher it is explained as to how to do it using firewall...
View ArticleRe: SRX cluster running two different versions of Junos. Easy fix?
Hi Milkman, First you should not keep running different Junos in HA devices,It might lead to issues.The best way to upgrade your scenario is connect the usb to the the device running junos 11.1)...
View ArticleRe: How long should an upload and install take
Hi The best way to upgrade the os is via USB method. I have done it hundreds of times with no issues.Please do the following.1) connect the usb to your srx100 (check the message comming in shel prompt...
View Article