SNMP mib-jnx-chassis.txt
Hi Experts, I have downloaded the latest Junos OS Enterprise MIBs for SRX1400 using Junos Release 12.1X46 and when I am trying to importing mib-jnx-chassis.txt using PRTG Paessler MIB Importer V2 it...
View ArticleRe: SNMP mib-jnx-chassis.txt
You will also need to include the SMI mibs: http://www.juniper.net/techpubs/en_US/junos12.1/topics/concept/juniper-specific-mibs-junos-nm.html [This for SRX as its the SMI for J/SRX]Structure of...
View ArticleRe: SNMP mib-jnx-chassis.txt
Hi,I'm not sure, try to upload it to /usr/share/snmp/mibs directory
View ArticleRe: Strange IPsec behaviour between SRXs
Dear Den, Your problem is in the connectivity between the SRX-01 and the device 192.168.3.21/24 if you're not getting a ping reply; becuase the reply left the SRX-01 correctly. It probably has...
View ArticleRe: Management access of SRX Chassis Cluster
Hi Rangaraj, Can you check whether backup-router config is added ? http://kb.juniper.net/InfoCenter/index?page=content&id=KB15580&cat=SRX_240_MGW&actp=LIST&smlogin=true -CKPlease Mark...
View ArticleRe: Why is the SRX using NAT-T for the IPSEC?
Hi It the exception rule, you need to use not local st interface but local physical interface on which IKE terminates.
View ArticleSRX to NS5GT Policy Based Vpn (ping not working)
HiI am setting policy based VPNs between SRX vs Ns5gt NS5GT----Ping Working ------SRX210SRX210---Ping Not Working----NS5GT ? I apologize very little english...
View ArticleRe: Strange IPsec behaviour between SRXs
Hello Hisham, Thank you for the reply. If that would be that simple, I would not disturb the community. Any device in 3/24 can ping the SRX-01 and vice versa. As for the switch - we are using the...
View ArticleRe: Strange IPsec behaviour between SRXs
Hello,The flow trace does not show anything out of the ordinary, next step would be to collect PCAPs on both machines, to verify if the ping/ping reply pkts are actually getting there.Before collecting...
View ArticleRe: SRX to NS5GT Policy Based Vpn (ping not working)
If you can post your SRX config that would be a good start? Also a 'show security flow session' when you try and ping from the SRX side
View ArticleRe: Juniper srx-100-b doesn't boot
If you have no output on the console and no pre boot prompt then there is likely no way to access the flash directly. This model the flash is soldered onto the main board. You could try to make a...
View ArticleDynamic VPN for remote workers
Good morning,I have a simple question. We have a number of users that are working from home that would need temporary access to network resources in the office which is using SRX device as a gateway...
View ArticleSYN proxy not working
Dear friends , Our main problem is spoof syn attacks are passing from the SRX 3600 . We have an MX 80 Router and we are routing firewall traffic to the SRX device. we do not put the gateways...
View ArticleRe: Dynamic VPN for remote workers
My question is this, is dynamic VPN supported by Juniper today? Short answer is Yes. would I be able to deploy it as described in the article below, is this document still valid? Yup, only caveat is...
View ArticleRe: Dynamic VPN for remote workers
Thank you elkadiki for your responce. Do you mind sharing your experience with it, any issues, tips? where can I find information about the supported client OS? i.e. Windows 8 Thanks again
View ArticleRe: Dynamic VPN for remote workers
It can be hard to configure at first ( as is the case with all dynamic VPNs in my experience ); but once it is configured it is stable. It is easier to configure from the Web Interface ( JWEB ) and...
View ArticleRe: SYN proxy not working
This command not working on SRX 3Kdebug proxy syn-floodAnd i could not find an alternate
View ArticleRe: SYN proxy not working
Hi,I'll try to find you the command for high-end deivces .I'm curious if you have checked the bad-ip-option counter if its increasing .show security screen statistics (zone zone-name | interface...
View Article