Re: logging traffic - log server
Hi, I've counted all recieved values from the logs and everything add up to 10531 - so is that mean that I only used 10531 bytes over few hours? Most records are tiny "sent": "64", "received": "48",We...
View ArticleRe: SRX300 series VLAN interface
Hi Regalis, Do not use the image of other SRX300 series on your srx 325 model, please wait until the image is released.They may be same series but there is some diference in the architecture of each...
View ArticleRe: Dynamic VPN, Pulse Secure Error 1453
How should I confirm connectivity towards the public ip? Google tells me that it is, in fact, my public IP (see public_ip picture).
View ArticleRe: source NAT allocation failure for a 0/0 source-nat interface
Hi Anand, Looks like CP does not have resource free for allocation. This should not be specific to one IP. Check the output of 'show security nat source rule all' a few times to see if the 'Failed...
View ArticleRe: source NAT allocation failure for a 0/0 source-nat interface
There are also known PRs related to this issue. It would be best to open a JTAC case to get confirmation. Regards,Srinath
View ArticleRe: Destination nat port forward issue
Yes you are correct. It should be .45 instead of .3. Sorry for the typo. Regards,Srinath
View ArticleRe: SRX3600 SNMP monitor timeout
- Is this SRX3600 in a chassis cluster?- Are you using fxp0 IP or some other revenue port IP to poll from SNMP server?If it is a revenue port, then check if interface has SNMP as host-inbound-service...
View ArticleRe: SNMP traps for IPSec tunnels
Hi, The issue still seems to be there. When the tunnel goes into hung state the packets won't encrypt or decrypt. Once that happens how will i be able to generate a trap or event. I am stuck with this...
View Articlesrx 210 when update on VPN wizard always get fail and can't update.
Ii'm fresh in setup on juniper. i need setup site to site VPN between srx 110 and srx 210, i try setup site to site vpn wizard on srx 110 no get any error, but i setup on srx 210 alway get error...
View Articleencrypting the srx configuration file
Hi all, there's an option to encrypt your config file on the srx: http://www.juniper.net/documentation/en_US/junos12.1x44/topics/task/configuration/security-configuration-file-encrypting.html It works...
View ArticleRe: kernel: watchdog: Time since last watchdog
Hey!The full syslog message is /kernel: watchdog: Time since last watchdog strobe: ....Have tried itwithyourproposal.Without success
View ArticleRe: VSYS query for migration from ISG to SRX
hello ,i am working on migration part ISG to SRX . we have multiple VSYS on isg and we are using only one LSYS for SRX. but i have created seprate routing-instance for each VSYS so my question is is...
View ArticleRe: Dynamic VPN, Pulse Secure Error 1453
I also tried using the VPN wizard in the Web GUI, but I'm getting the same error.
View ArticleSRX3600 IPsec VPN (Base-route): Multiple Phase-1 SAs for Same Gateway
Hi All Now ,in this Case, throuht command "run show security ike security-associations ",find Multiple Phase-1 SAs for Same Gateway， but IPsec sa only one . 3004773263 UP 691ac4504cbe66b1...
View ArticleRe: kernel: watchdog: Time since last watchdog
Sorry, I just noticed that your match criteria is only under the file logging. You need to have your match also under the syslog host you want to send the messages to. host x.x.x.x { any any;...
View Article[partition] option in [request system software add] command
In 15.1X49 @SRX300 series, Is not support [partition option] in the command that is [request system add software]? I tested two versions of 15.1X49 that the one is D35 and the other one is D45.My SRXs...
View ArticleRe: [partition] option in [request system software add] command
The option is only needed on certain models. This option was created in Junos 10 when the new feature of an alternate boot partition was added to Junos. this allows the boot recovery of the device...
View ArticleRe: [partition] option in [request system software add] command
Hi spuluka-san, As my understanding regarding the feature of [partition] option is, 1.Content that you showed2.Can upgrade or downgrade both partitions at once. Regarding No.2. I know that that by...
View ArticleRe: [partition] option in [request system software add] command
The partition option is not supported on the SRX300. Only on these devices listed in the documentation. Note: Partition install is supported on the default media on SRX100, SRX210, and SRX240 devices...
View Article