Re: SRX300 - 18.2R3-S1.7 - smid_register / sdb_db_init failed
Hi, This seems to a known issue where the DHCP might be having issues and the service release under 18.2R3-S1 are the only ones affected....
View ArticleRe: Firmware version 12.1X46-D86 issues
As the product SRX100B/H is End of Life and End of Support, I doubt if the recommended version will be further updated. Regards,Pradeep Kumar M
View ArticleRe: SRX 340 tranparent mode cluster SNMP configuration
Hi aungzawtun, I have 2 srx340 to configured as cluster in transparent mode. I have checked online for documentation all I get is the cluster config in routed mode. Could you please share your full...
View ArticleI doubt in configuring irb interfaces, why doesn't it ping me?
Good afternoon, can someone tell me why I get ping 192.168.100.10 and 192.168.8.1 no? if they are configured the same and another question, is it possible to add several interfaces to a virtual router?...
View ArticleSRX Transparent Mode Clustering - Unable to ping through
Hi All, Could someone please help me with this issue. I have 2 SRX340 to cluster, however I have setup a lab on EVE to configure and test before configuring the SRX340. I'm unable to ping from the PC...
View ArticleRe: Jweb Incorrect user/password after Junos upgrade on SRX
Hello, I am stuck with the same issue.It's been several months since there is no fixTo use the Jweb interface which version should I install? Best regards Gilles
View ArticleRe: UBS Port Console Access
Sure, I can see it. I have played withe the settings in SecureCRT and cant get a live connection to it. These are my settings; BAUD 38400DATA: 8PARITY: NONESTOP BITS: 1 Is that correct?
View ArticleRe: UBS Port Console Access
The default settings are 9600 8N1.. So try changing your baud rate and revert with the result.
View ArticleClik here to view.
Re: UBS Port Console Access
Success, thanks. Not working on a colleagues machine but working on mine
View ArticleRe: SRX Transparent Mode Clustering - Unable to ping through
There are several issues in the provided config: fxp0 on each node in the chassis cluster does not support switching. You should change to "family inet address 192.168.254.53/24" insteadTo do switching...
View ArticleRe: Firmware version 12.1X46-D86 issues
So this is your excuse for stiffing me with bad firmware? More encouragement to go to a different vendor for my network equipment in the very near future.
View ArticleRe: SRX Transparent Mode Clustering - Unable to ping through
Hi, Thanks for getting back to me. Not completely sure if I understand you. However, I have SRX340 that will be clustering on Monday.This is the config that I have come up with base onmy understanding...
View ArticleRe: Firmware version 12.1X46-D86 issues
Well, every vendor stops pushing updates at one point. In this case the SRX100B and SRX100H has not been sold since May 2014, more than 5 years ago. Providing software updates after 5 years is usual in...
View ArticleRe: Firmware version 12.1X46-D86 issues
some of us can manage via cli, some cannot. I'm just wondering why we are accepting bad firmware from Juniper. Windows 7 is eol but Microsoft still occasionally patches it.
View ArticleRe: Firmware version 12.1X46-D86 issues
Post 12.1X46-D66, it has been an Extended support for SRX100B/H series devices which eventually ended with 12.1X46-D86 on 10th May 2019. FYI, similar end of extended support for Microsoft is Jan 14,...
View ArticleRe: HSRP Feeds from ISP to clustered SRX 240 pair
What is the right tool for the job then? We are experincing the same issues. We have SRX340 and the DataCenter uplinks are seeing active/active issues. How do you go about fixing this?
View ArticleRe: I doubt in configuring irb interfaces, why doesn't it ping me?
Hi, Yes you can have more than one interface in a virtual-router. However, to help you with the ping situation I need to better understand your topology that I assume it looks like this, please confirm...
View ArticleRe: I doubt in configuring irb interfaces, why doesn't it ping me?
Hilpaniagua.What I intend with my topology is in an interface, to have 2 or more virtual routers that distribute ips with DHCP server regardless of the VLAN they access, what they ask me is to bridge...
View Articletest config terminal syntax error on }
I loaded a config in Notepad++ and cut/paste into the terminal and got: > test configuration terminal [Type ^D at a new line to end input] ## Last changed: 2019-08-30 05:57:27 GMT-8 version...
View ArticleRe: test config terminal syntax error on }
Hello, wrote:Seemingly I have an error with a curly bracket, or is it something else? I tried replacing tabs with spaces. I'm pasting into a Mac terminal using screen. You have likely made an error...
View Article