Re: Issue communicating with Network from SRX300
Ping/traceroute datacenter ip using irb.1 interface ip as source (10.255.7.1) from SRX.
View ArticleRe: traffic only flows in one direction through routed based VPN between srx...
As per the flow trace, SRX passes the traffic successfully from 172.16.3.52 to 172.30.10.4. You may have to check at PC which is having IP 172.30.10.4. Is there any kind of desktop firewall installed...
View ArticleUBS Port Console Access
Is it possible to use the supplied USB cable to give console access to an SRX? I have downloaded the drivers to enable this but despite playing with the settings in SecureCRT, I am unable to get this...
View ArticleRe: Issue communicating with Network from SRX300
That command does work, thank you. Still cannot figure out why disconnecting the switch makes SRX unreachable though.
View ArticleFirmware version 12.1X46-D86 issues
After upgrading an SRX100 router to 12.1X46-D86 i cannot log into it through web gui. I can ssh to it with same accounts though. I installed it because its currently a jtac recommended version.
View ArticleDHCP Issues with SRX300
Hello, Clients obtaining an IP from the 10.255.7.160 pool cannot connect to the outside world. They obtain an IP. I can ping them from the SRX. I can ping 8.8.8.8 from the SRX. But the clients cannot....
View ArticleExtract JunOS 11.4R7.5 firmware from SRX Gateway
Hello The release 11.4R7.5 is not downloadable anymore. Is it possible to extract the firmware release from an existing device? Model: srx240hJUNOS Software Release [11.4R7.5] Could you help me to...
View ArticleRe: Firmware version 12.1X46-D86 issues
Hi, Kill the httpd process and try to access the device again via web gui. Eg: {primary:node0} root@E_HHA02_EXT_FW01> show system processes extensive | match http 1749 nobody 1 96 0 8148K 3604K...
View ArticleRe: Firmware version 12.1X46-D86 issues
Technically i did as i restarted the router to see if it would fix it.
View ArticleClik here to view.
Re: Extract JunOS 11.4R7.5 firmware from SRX Gateway
Hi Dario, You can create a snapshot to a USB making it a bootable and use it to boot another SRX device of the same model. Refer to https://kb.juniper.net/InfoCenter/index?page=content&id=KB29811...
View ArticleRe: Firmware version 12.1X46-D86 issues
Hi, I missed the point that same accounts work for SSH and that you can get to the login page but the credentials just don't work. Just checked and found the below thread with similar issue which...
View ArticleRe: UBS Port Console Access
If you have installed the drivers and plugged the usb cable from your PC to the mini-USB port, does the serial port show up in you device manager? It should register itself as a COM port with next...
View ArticleRe: DHCP Issues with SRX300
Would be nice to see which IP settings the client(s) are provided via DHCP. One thing which points out is this config line:set access address-assignment pool GuestWifiPool family inet dhcp-attributes...
View ArticleRe: st0.6 interface not coming up IPSEC VPN
So tunnel fails in IKEv1 phase 1 in packet exchange number 3/4.Most likely a configuration issue. I would check the configuration on both the peer devices again. Also in the logs i see the SRX trying...
View ArticleRe: Extract JunOS 11.4R7.5 firmware from SRX Gateway
Also if you have an active support contract you can open a ticket and get copies of no longer posted firmware from support.
View ArticleRe: Issue communicating with Network from SRX300
The virtual irb interface require that at least one physical interface in that vlan be up for the virtual interface to come up. So likely you have all the vlans on a trunk port facing the switch....
View ArticleClik here to view.
SRX300 - 18.2R3-S1.7 - smid_register / sdb_db_init failed
I just upgraded an SRX300 to 18.2R3-S1.7 (as listed on the recommend junos software page) and syslog is filled with: Oct 17 21:14:07 jnx repd[2078]: sdb_db_init: Failed to init stats db, err:-2DB out...
View Article