Re: Port Forward and DMZ Help.
I tried your command on my SRX and it worked fine: set security nat destination rule-set dst-nat from zone untrust I think your mistake would be on the ";" at the end of command, you should try it...
View ArticleRe: Port Forward and DMZ Help.
After some test: set security nat destination pool pool_NAS address 192.168.5.160/32 set security nat destination rule-set Nat-Inside from zone untrust set security nat destination rule-set Nat-Inside...
View ArticleRe: Port Forward and DMZ Help.
My updated full conf: ## Last changed: 2016-10-22 04:33:09 CESTversion 12.1X46-D55.3;system { host-name JuniperSRX210; time-zone Europe/Rome; root-authentication { encrypted-password "password"; }...
View ArticleSRX Dynamic VPN license
Dear all, I has SRX device has license status as below: License usage: Licenses Licenses Licenses Expiry Feature name used installed needed idp-sig 0 1 0 2016-11-21 00:00:00 UTC dynamic-vpn 0 2 0...
View ArticleRe: SRX Dynamic VPN license
Hi , Please check this . https://kb.juniper.net/InfoCenter/index?page=content&id=KB22617&actp=search You should be able to configure and use upto two dynamic-vpn users .
View ArticlePort Forward configuration check
Helping with this threadhttp://forums.juniper.net/t5/SRX-Services-Gateway/Port-Forward-and-DMZ-Help/td-p/298917 I've made this conf on my Juniper SRX210BE: ## Last changed: 2016-10-23 15:44:44 CEST...
View ArticleRe: Port Forward configuration check
Hi, I assume that you want to do port forwarding to the internet, the configuration is incorrect :- from interface vlan.0 - The from interface should be your external interface.destination-address...
View ArticleRe: RPM not working quite like I expect
Hi, once it detects the primary SDWAN connection is offline it fails over to the Cellular carrier.--- this can be seen from the default route next-hop change . If the SDWAN comes online, is the...
View ArticleRe: Port Forward configuration check
Thanks for your reply.Now using your suggestions dyndns service appear as working but the ports are already closed.Here it is updated conf: ## Last changed: 2016-10-23 21:55:59 CEST version...
View ArticleRe: export network between routing instances
Can you see the session setup? show security flow session destination-prefix xxxxx Need to review the security policies from the ingress to the egress interface zones to make sure the https traffic...
View ArticleRe: SRX Chassis Cluster With BGP Router for Dual Internet
to run the iBGP peers on both SRX you will need to convert from Active/Passive to Active/Active setup.
View ArticleRe: commit failed
The basic file clean up command may also be helpful here. request system storage cleanup
View ArticleRe: Trying to configure 2nd WAN connection in J-Web
The web UI is limited on the SRX and many scenarios are not covered. This example of dual ISP with failover should give you what you need for the dual routing instances, security and nat policies....
View ArticleRe: Clientless VPN to SRX not possible?
I agree that remote access VPN is a huge hole in the Juniper security portfolio here. There are serious limits as you outline on the use and also further limits on specific platforms and software...
View Articleconfig VPN on SRX failed
Dear all, I config demo VPN on SRX240, config in attachment, I connect directly PC to ge0/9 of SRX, and can ping 172.18.1.2 but when i using VPN Pulse Secure to connect 172.18.1.2 has error:...
View ArticleClik here to view.
Re: Apple iPhone/iPad VPN to Juniper SRX - now possible!
Hey Milan, Would love to get this going. Do you know if this would be possible without an external RADIUS server? I know the "Dynamic VPN" can use local accounts on the SRX itself, but can only use a...
View Articlefilter-based routing.
Hello. I ma trying to set up filter based routing and cant get it working. Everything seems fine to me.1. Applied firewall filter to interface:show interfaces vlan unit 20 family inet { filter { input...
View ArticleRe: VLAN Routing between different zones
Hello Ron, thanks for help and please excuse my bad english.Now i put the address, wich you mean with following commandlines set forwarding-options helpers bootp relay-agent-optionset...
View Article