Quantcast
Channel: All SRX Services Gateway posts
Browsing all 17645 articles
Browse latest View live

Re: Force SRX to boot from usb

I see below option from shell to chnage the boot sequence to USB, again I havent tested this , i just found I can configure this. root@SRX% sysctl -w machdep.nextbootdev=usbmachdep.nextbootdev:...

View Article


Re: SRX220H2 VPN Help

I would recommend you opening a case with JTAC for further/detailed investigation.

View Article


Re: Upgrade SRX210H from 10.4r3.4

Can you check the  system time and make sure its showing the current time? Usually this error (certificate validity) comes because of an old time active on device. root@SRX> show system...

View Article

Image may be NSFW.
Clik here to view.

Re: Upgrade SRX210H from 10.4r3.4

Hello Dough , From 10.4 version we can directly upgrade to 12.1X46 version since its Extended EOL version , so we can Junp 2 EEOL versions .But since its failing from your end , Try upgrade to 11.4...

View Article

Re: Qos in test shows high ping times

Transit Ping traffic should be treated as any other traffic. Do you have same priority/buffer for Voice and Ping? If you have higher priority for voice then what you see can be an expected behavior.

View Article


Re: SRG 320. IPSEC vpn worked then got flakey

I think this may be a VPN issue (data flow through VPN) , do you have VPN monitoring enabled? Can you turn it on and check the behavior to make sure the tunnel always pass traffic.

View Article

Re: Site to Site VPN between a SRX w/dynamic IP to SRX w/static IP

Try adding below config on SRX210 side.  set security ike gateway gw_Quan general-ikeid   delete security ike gateway gw_Quan no-nat-traversalcommit and if the problem continues collect below output...

View Article

Re: Qos in test shows high ping times

This in our lab all other questions were idle except the control Even if control is idle the time still goes up

View Article


Re: Qos in test shows high ping times

Can you check the RTT without cos? 

View Article


Re: Two Policy based VPN with automatic failover

Hi Bhaskar, You can achieve redundancy on Policy based VPNs as well.  Please check: https://kb.juniper.net/InfoCenter/index?page=content&id=KB29211&actp=search Regards,Anand

View Article

Re: cisco asa to juniper srx vpn site to site not working !!!!

Sorry for the confusion,  There are TWO independent differences between the ASA configuration posted and your SRX config.  IKE versionSRXVersion: IKEv1ASAIKEv2 As mentioned you need to configure IKEv2...

View Article

Re: cisco asa to juniper srx vpn site to site not working !!!!

Hi Team, First thing to remember is that CIsco ASA crypto ACL does not support application ports. You can configure them however they will not be off any use.So you can only configure the Crypto ACL...

View Article

Re: How to configure multiple hw-addresses on one interface

After getting the service installed, it turns out that dhcp is not required to pull the IP. The customer gw does only allow one IP to forward to one MAC. When I tried with proxy-arp and pinged for a...

View Article


Re: Upgrade SRX210H from 10.4r3.4

There is a possibility that I tried this before I got NTP going on the box. I will try again tonight in case those happened in the wrong order. I will let you know. Thanks. -Doug

View Article

Re: Upgrade SRX210H from 10.4r3.4

There is another 210 that is an HE version (opposed to this one's H version) that is running 11.2R4.3. I was scared I was going to brick this one since they are a little different. Mine:Model:...

View Article


Re: Upgrade SRX210H from 10.4r3.4

The software is the same between the two devices. You could upgrade from that package.Sent from my Sprint Samsung Galaxy S7 edge.

View Article

Dynamic VPN

Hicurrenlty have 5.0 Dynamic VPN but adding Windows 10 laptops and they arent recognised. I believe I need to upgrade and believe Pulse Secure has a 5.2 version. Is there anywhere I can download this

View Article


SRX300 guided setup fail, syntax error

Dear all, i have reset the SRX300 and try to config again. When I commit, it shows the configuration could not be unlocked and 2 syntax errors. My firmware version is 15.1X49-D60. How can i solve it? I...

View Article

Re: SRG 320. IPSEC vpn worked then got flakey

Ok, I've enabled it - what am I looking for?

View Article

SRX220 /jail/var over capacity

Hi Everyone, Total Juniper n00b here. Our SRX220 with JUNOS 12.1X44 is running slow and after doing some digging around I learned about System Storage and that it's normal for some things to be at...

View Article
Browsing all 17645 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>