Re: Upgrade SRX210H from 10.4r3.4
It fails when I try to do the upgrade. The error messages upon failure was the google fodder than led me to learning about the "3 release" rule. I saved the output of the failure: SRX210> request...
View ArticleRe: How to configure multiple hw-addresses on one interface
I would lease the /29. AT&T puts this on the LAN side of their required customer GW and uses the high address for their equipment and I can use the other 5. I already have NAT working well and I...
View ArticleForce SRX to boot from usb
Hi, I have an SRX cluster running 12.1X44-D40.2. Seems like on one node the CF has died, now it boots up, enters multiuser and crashes. I did some reserch on the internet, and, according to the...
View ArticleRe: Force SRX to boot from usb
Hey, I am unsure if you are able to boot up the device to the cli mode before the device crashes.In case you are able to reach until the operational mode you can use the below command to force the SRX...
View ArticleSRX220H2 VPN Help
Hi, I recently upgraded the Junos software on two SRX220H2s. The two units create a VPN, over the VPN we have a shared ip phone system. Since the upgrade our phone system has had an issue on the side...
View Articlerate limiting video streaming
Hi Experts, could you guys give me a link the "how to" configure rate limiting video streaming on srx. would it be much better if we use APPQos to rate limit video streaming? many thanks!
View ArticleRe: How to configure multiple hw-addresses on one interface
Hello there,How do You plan to handle DHCP lease expiration event?ThxAlex
View ArticleRe: Force SRX to boot from usb
Yeah, I was able to boot up to multiuser, but then crash follows in like 10 seconds, so it's impossible to ussue a command. I've ended up downgrading from 12.1X46-D60.4 to 12.1X44 using tftp boot...
View ArticleTwo Policy based VPN with automatic failover
Is that possible to create two Policy Based VPN's with two ISP's , so that if one ISP fails then traffic will failover to the VPN tunnel created on other ISP.I have few subnets for which I want to use...
View ArticleRe: cisco asa to juniper srx vpn site to site not working !!!!
i change the vpn from route to policy based vpn and this is the configuration root@site-a-dahra-ly# show |display set |no-more set version 12.3X48-D35.7 set system host-name site-a-dahra-ly set system...
View ArticleHow to update Mini-PIM firmware???
Does anyone know how to update mpim firmware supplied here (https://www.juniper.net/support/downloads/?p=docsis#sw)? Thanks!
View ArticleRe: SRX firewall routing configuration
Hi, while reviewing the outout ofshow route command, one output lines i started to dig about shows as681 10.14.224.193/32 *[Local/0] 24w6d 22:05:53682 Reject i tried to...
View ArticleRe: cisco asa to juniper srx vpn site to site not working !!!!
Simply changing to policy-based VPN will not resolve the issue, if the other side is not configured as policybased. Secondly, the ASA is using IKEv2. You did not configure IKEv2 when you were using...
View ArticleRe: rate limiting video streaming
APPQoS would be best if your system and license supports it. However you could use a policer to rate video streaming if you know what ports the traffic is using. Here is an example for ftp, you would...
View ArticleRe: Critical processes
Hi, IMO, every process has its own dedicated tasks and are equally important. It depends on what type of issue, you are experiencing. For example, if it is a routing issue, RPD(routing protocol daemon)...
View ArticleRe: How to update Mini-PIM firmware???
You may follow KB27918 https://kb.juniper.net/KB27918
View ArticleRe: rate limiting video streaming
You may refer Chapter 11:http://www.juniper.net/techpubs/en_US/junos/information-products/pathway-pages/security/security-application-identification.pdf...
View ArticleRe: Critical processes
"show system processes extensive" shows the process that are active on your device and it depends on your configuration and services you have enabled. But you should not be worried if your system...
View ArticleRe: Two Policy based VPN with automatic failover
Is there any specific reason for using policy based VPNs? if not you can follow KB29227 to achive this with route based VPNs. https://kb.juniper.net/KB29227
View ArticleRe: Force SRX to boot from usb
I never tried this my self, just thinking if we can chnage the current boot media to USB from U boot like below => setenv boot.current usb I have seen using this command to chnage boot sequesnce to...
View Article