Re: the issue with pbr on SRX
Great!!! it's very useful for me . Many Thanks!!!!!!!!!!!!!
View ArticleDestination NAT/Port NAT - Totally confused and in dire need of help
I've been getting my butt kicked by this - about 20 hours so far - and completely baffled.I have an Amazon VPC with two subnets - Public and Private. Within the private subnets have two VM's.I have an...
View ArticleRe: Destination NAT/Port NAT - Totally confused and in dire need of help
Hi DaleM, Configuration looks good.Is it possible to configure flow trace and see why is the packet getting dropped or is it actually reaching the SRX from internet side or not. regards,Guru Prasad
View ArticleRe: Destination NAT/Port NAT - Totally confused and in dire need of help
I have copied the entire configuration here.I'm not sure how to setup a "flow trace".I do have other rules that allow remote access to resources on our internal network. The servers in the Amazon VPC...
View ArticleFirewall stuck
Hi I have SRX 3600 firewall. It gets stuck at => prompt. I set env settings (e.g. ipaddr, serverip, subnetmask) and then try to load the loader to upgrade new device firmware via tftp. But device...
View ArticleRe: Destination NAT/Port NAT - Totally confused and in dire need of help
Hi Dale, Please refer the below mentioned article and provide us with output of flow trace which help us to locate the exact issue and suggest you a solution : #...
View ArticleRe: Firewall stuck
Hi Arslan? Do you have another workinng SRX3K/1K device? If so we may try taking a snapshot from that booting this node.
View ArticleRe: SRX Route VPN - Random tunnel tear downs
I would recommend you opening a JTAC case for further investigation on ikeV2.
View ArticleRe: Firewall stuck
Thanks Suraj Thanks for reply .I dont have anyother srx 3600 right now but trying to manage from somewhere. Meanwhile can you help me about how to take snapshot on usb stick and than how to boot the...
View ArticleRe: Firewall stuck
you can take snapshot using " root> request system snapshot media usb partition". Plugin the USB and run this command, once its completed you can use this USB to bootup another SRX.Or the other...
View ArticleRe: Firewall stuck
you can take snapshot using " root> request system snapshot media usb partition". Plugin the USB and run this command, once its completed you can use this USB to bootup another SRX.Or the other...
View ArticleRe: Firewall stuck
Once a gain thanks rsuraj for your reply. I have one more question as your earlier post you suggest to take snapshot from anyother working srx 3600 unit If I get the system snapshot from another...
View ArticleRe: Firewall stuck
Step 1. Power down the faulty nodeStep 2. Plugin USB with snapshot to faulty device REStep 3. Power on faulty node, device will automatically try to boot from USBStep 4. Once device booted up execute...
View ArticleRe: Firewall stuck
Step 1. Power down the faulty nodeStep 2. Plugin USB with snapshot to faulty device REStep 3. Power on faulty node, device will automatically try to boot from USBStep 4. Once device booted up execute...
View ArticleRe: cisco asa to juniper srx vpn site to site not working !!!!
Your output is still showing that the SRX is sending IKEv1 and the ASA is setup for IKEv2. You need to add the IKEv2 setup to your SRX.set security ike gateway ike-gate-SITE-A-DH...
View ArticleRe: GRE over IPSEC to a cisco
It has been a while but I've used this type of configuration for compatibility and it does work. In a Juniper to Juniper connection you don't need the GRE tunnel but can use a route based VPN and make...
View ArticleRe: srx340 as a switch and gateway router
Hi, I have 2x SRH240H2 available which have been running as a cluster in my cloud setup for about 4 years. Both have running fine without any issues ...
View ArticleRe: Help with a vpn configuration
The messages suggest that these sections of your SRX config do not match the settings on the Fortinet. proposal Phase1 { description phase1; authentication-method...
View Article