Re: SRX210 accepts any password entered for any user via ssh or jweb/http
Abed AL-R wrote:Hi, Have you tried this : http://rtoodtoo.net/srx-password-resetrecovery/ If not worked out , could you attach the output of :# edit system login# show | display set Does this issue...
View ArticleRe: SRX210 accepts any password entered for any user via ssh or jweb/http
pk wrote:Hi Are you sure the connections were actually successful?Or maybe just some confusing log messages? What's your software version? (use "show version") Do you have any external authentication...
View ArticlevSRX Interface ordering in VirtualBox
Hi all,I'm having a nightmare trying to provision an 8 port Juniper vSRX 12.1X47 in a lab environment.Every time I boot it, the NIC's don't line up at all.IE, NIC 1 -> ge-0/0/6NIC 2 ->...
View ArticleRe: SSG and SRX VPN Problem
Althought I use set ike soft-lifetime-buffer <seconds>phase 2 still can't come up. Regards
View ArticleHave an issue with routing instances
I need route a machine on my network to the second IP from my ISP, but I'm having trouble, don't work!!My scheme is: ISP: ge-0/0/1 IP: 200.55.125.149 / 200.55.125.153 / 200.55.125.154 /...
View ArticleRe: Question about routings!!
Joses don't need to use vlan-tagging and 1 unit per IP to make routing???
View ArticleRe: SRX210 accepts any password entered for any user via ssh or jweb/http
Hi Jesse G, Why don't you consider upgrading the JunOS ?
View ArticleIDP Signature Update On SRX650
Hello All, Want some knowledge on how can i offline update signature on my SRX650. Where and how to download the signature file and how to use that file to update signature in my SRX650. The version on...
View ArticleRe: Console access to SRX without serial?
We use the AirConsole product for feild work. this allows you to connect to a console port over wireless. So no serial port is needed at all on the user device. We use this on tablets even. This is...
View ArticleRe: Have an issue with routing instances
Hi Marc , From your requirement ,it seems to me that you want to translate (source NAT) your internal addresses as below - Instead or routing them As there is only one gateway (.254) - single ip on...
View ArticleRe: Vpn created behind NAT device
Yes, those are the only ports required for your VPN connection. If you are having problems getting the tunnel to come up see the verification section of this document for the troubleshooting commands....
View ArticleRe: SSG and SRX VPN Problem
There does not seem to be much information about this message around. You could try to enable the VPN monitor on the SSG and use ping to a specific address reachable across the tunnel. I've found this...
View ArticleRe: IDP Signature Update On SRX650
I think this is the documentation you are looking for. http://kb.juniper.net/library/CUSTOMERSERVICE/GLOBAL_JTAC/technotes/SRX-IDP_Offline_SecurityPackage_update.pdf
View ArticleRe: configuring the VDSL2 PIM with point to point IP without using username...
hello rsuraj , first thanks for your helpI configured the below configuration,but i can't still ping the point to point I want to use the VDSL2 PIM as the SHDSL configuration like this one set...
View ArticleRe: configuring the VDSL2 PIM with point to point IP without using username...
Is the at-1/0/0.0 interface showing link up in show interfaces terse? Is the address of the interface showing active under show route? If your are doing the ping from an internal device is there a...
View ArticleIPsec tunnel up but no traffic
Hi, I'm trying to configure a static ipsec tunnel between an SRX240 and a Linux host (using racoon). It is now to the point where I have the security-associations showing so the tunnel seems to be...
View ArticleRe: IPsec tunnel up but no traffic
Do you have a static route pointing the 172.16.41.0/24 subnet to the st0.0 interface? If so, is this route active in show route to the correct interface? Also, your security policy is correct for ping...
View ArticleRe: IPsec tunnel up but no traffic
Hi, I didn't add a static route manually, but because of the interface address being /24, it appears as though there is a route out st0.0: root@fw01> show route ... 0.0.0.0/0 *[Static/5] 32w6d...
View ArticleRe: IPsec tunnel up but no traffic
You don't want that subnet on your st0.0 interface if this is the remote LAN segment. This causes the SRX to see the subnet as local and layer2. you can just make the st0.0 interface unnumbered in...
View Article