Re: SRX300 Active/Backup
Hi Shailesh, thanks for your reply! I already saw the figure you posted and I think that could be a good solution to my problem, but I have a question: what happens if at the same time i get the...
View ArticleSRX340 and SRX-MP-1SFP-GE
Hi, Is the SRX-MP-1SFP-GE compatible with the SRX340? I've been trying one but am getting some very strange issues, the SRX sees the module and identifies it correctly (as a 1xGE High Perf SFP mPIM)...
View Articleadvertise OSPF static routes into stub/t-stub
is it possible to adverise static routes into these? we have some SOHO routers that come back to and SRX 240 ( about 30 of them each SOHO bring up OSPF when the tunnle comes up this is so i dont have...
View ArticleRe: advertise OSPF static routes into stub/t-stub
Hello, Andrewmiller wrote:is it possible to adverise static routes into these? No. See RFC 2328 section 3.6https://www.ietf.org/rfc/rfc2328.txt Andrewmiller wrote: 240 (st0.0 to st0.36)ospf {...
View ArticleRe: advertise OSPF static routes into stub/t-stub
i need a set of routes (that are internet IPs) to get advertised to all the SOHO via OSFP that way I do not need to put the static routes on the each SOHO device these are a new project and it seems...
View ArticleRe: advertise OSPF static routes into stub/t-stub
from the SOHO boxes traceroute 199.38..x.x this tries to trace out hte internet, but i need it to go over the IPSEC tunnle bock to our HQ once it hit the HQ the routes in our core send to to a FW...
View ArticleRe: SRX340 and SRX-MP-1SFP-GE
Hi benj5, Cannot find anything conclusive but I would not expect it to be supported when looking at the following: 1. SRX-MP-1SFP-GE is only listed as an accessory for SRX550 and SRX650 in the official...
View ArticleClik here to view.
Re: advertise OSPF static routes into stub/t-stub
Hello,Your options at this point:1/ convert area 50 stub into normal area->visit each SOHO box to change config2/ use BGP overlay -> visit each SOHO box to change config3/ on SRX 240 only, delete...
View ArticleRe: SRX340 and SRX-MP-1SFP-GE
Same with me - I tried to use this MPIM, just as an experiment. At first it was working (show chassis hardware and show interfaces), but after that flowd and chassisd started core-dumping repeatedly,...
View ArticleRe: advertise OSPF static routes into stub/t-stub
I think BGP would be the least invasive, since i will not need to bring down the OSPF to do it. also # 3 would work im sure I'm assuming i would have to write a policy for it to work ? like this ?...
View ArticleRe: reboot srx 240
Hi rsuraj, I went to the config mode and issued the command you've mentioned, "show system services". Yes, I'm able to see the configuration. So, I'm really stumped why this keeps happening. The only...
View ArticleSite To Site
hello guys, i need some one the shade some light on my problem,i have JUNOS 15.1X49-D60.7 and Im Trying to do site to site to a Cisco on the Other POINTthis is my JuniperModel: srx300Junos:...
View ArticleRe: Site To Site
by the way , i did my command with the help of this sitehttps://www.juniper.net/support/tools/vpnconfig/#vpnSettings
View ArticleRe: SRX340 and SRX-MP-1SFP-GE
Thanks for the replies. I'd seen the SRX300 didn't actually list the module (but only after I'd tried it) but as you say couldn't actually find anything definitive about support for it. It would have...
View ArticleRe: SRX300 Active/Backup
Is there a way to configure bgroup interface on Junos SRX or redundant interface (but in the same node) ?
View ArticleSRX300 cos on st0 and ge-0/0/0
Dear Professional, we have 2 subnets, 192.168.15.0/24 on ge-0/0/1.0 and 192.168.5.0/24 on ge-0/0/2.0. ge-0/0/0.0 is connected to WAN.We setup IPSEC VPN from the subnet 192.168.5.0/24 and assign to...
View ArticleRe: SRX300 Active/Backup
Hi , You can achieve what you are lookig for if you have all the interfaces in one reth.However, this would require the Switches to be in STack to avoid packet drops.
View ArticleRe: COS on st tunnel interfaces
Starting with Junos OS 15.1X49-D60, class of service (CoS) features such as classifier, policer, queuing, scheduling, shaping, rewriting markers, and virtual channels can now be configured on the...
View ArticleRe: SRX300 cos on st0 and ge-0/0/0
As suggested in below link;https://forums.juniper.net/t5/SRX-Services-Gateway/CoS-over-a-IPSec-tunnel/td-p/62727 if you want all esp traffic to have higher priority over other traffic , you can create...
View Article