Re: RT_FLOW : APPTRACK_SESSION_CLOSE: How to disable
Hello, According to the link below: AppTrack log information is also contained in firewall logs so long as another AI component is enabled like AppFW or AppQoS. Typically, this is best leveraged by...
View ArticleRe: Dynamic VPN on Loopback Interface
Hello, I think termination of dynamic VPN on loopback is not supported. https://kb.juniper.net/InfoCenter/index?page=content&id=KB26027&smlogin=true&actp=search Regards, Rushi
View ArticleRe: RT_FLOW : APPTRACK_SESSION_CLOSE: How to disable
So after 137 days of being up, i rebooted the system and changed the logging to; syslog { archive size 100k files 3; user * { any emergency; } host [IP] { any emergency; authorization any; user any; }...
View ArticleRe: SRX 3600 Memory Upgrade?
Thank for the information, I guess it would require a full upgrade to a higher end model then?
View ArticleRe: srx340 as a switch and gateway router
the SRX110 and SRX220H2 did not go EoL - but I agree, there are too many features missing without a reasonable alternative (no dynamic vpn, no NAT or VPN-termination on IRB-interfaces - and the worst...
View ArticleRe: srx340 as a switch and gateway router
Actually you are right, I was a little hasty. The others are End of Sale however.
View ArticleRe: GRE over IPsec on SRX5800 JUNOS 12.1
Hi Steve, Thanks for your feedback! It helps a lot. Sorry but for the route part, based on my understanding of the example GRE over IPsec, I think it may should be "the routes to those remote side ip...
View ArticleRe: SRX 220 Reth interfaces and VLAN
Hi Sayful, I think you have terminated the Vlan 192 in reth interface (reth1.192 which has IP 192.168.2.252/24) ,and for the same vlan you have created another L3 interface vlan.192 ( and assigned an...
View ArticleRe: SRX Dynamic VPN access route
Hi , Could you please share the complete configuration and software version information ?
View ArticleRe: GRE over IPsec on SRX5800 JUNOS 12.1
In your case the only address routing across the IPSEC tunnel will be the GRE tunnel address. Anything that is routed to the IPSEC tunnel will be immediately encapsulated and sent down the tunnel for...
View ArticleRe: SRX Dynamic VPN access route
I assume that the pulse is showing connected. then follow these steps to gather information on where the connectivity issue is. http://kb.juniper.net/InfoCenter/index?page=content&id=KB17660 To...
View ArticleRe: Differentiate between NAT types
Hi Ben, In your show (show security flow session ) command /snippet, Application traffic control rule-set: INVALID, Rule: INVALID Does it mean NAT has allowed even though rule-set saying Invalid ? I...
View ArticleSRX won't boot and won't start "loader.
Small SRX stop to boot.Boot process looks like this: U-Boot 1.1.6-JNPR-2.7 (Build time: Nov 26 2013 - 19:04:49)Initializing memory this may take some time...Measured DDR clock 266.62 MHzSRX_100H2 board...
View ArticleRe: Differentiate between NAT types
Brju wrote:Hi Ben, In your show (show security flow session ) command /snippet, Application traffic control rule-set: INVALID, Rule: INVALID Does it mean NAT has allowed even though rule-set saying...
View ArticleRe: SRX 3600 Memory Upgrade?
The memory on the routing engine should be capable of handling a couple of full BGP route feeds. Otherwise it wouldn't effect performance of the network traffic through the device. If you are looking...
View ArticleRe: Differentiate between NAT types
Thanks BenOzark777 wrote: Brju wrote:Hi Ben, In your show (show security flow session ) command /snippet, Application traffic control rule-set: INVALID, Rule: INVALID Does it mean NAT has allowed even...
View ArticleRe: srx340 as a switch and gateway router
I too have been unable to get this type of basic service working on an SRX345 running JunOS 15.1X49-D45. I tried the following configuration: system { services { ssh; web-management {...
View ArticleGr-0/0/0 and st0 must have family inet address?
Hi Experts, I have two questions about GRE tunnel over IPsec: http://kb.juniper.net/InfoCenter/index?page=content&id=KB19372&actp=search&viewlocale=en_US&searchid=1345331927176%3CBR%3E...
View Article57 lines of address book entry becomes 55 in show | compare | count?
HI all On the srx, I tried to commit 57 lines of address book entries. But once I did and do the show | compare | count it says the number of lines changed is only 55. How come? Thanks
View Article