Re: 57 lines of address book entry becomes 55 in show | compare | count?
Hello, Could there be any duplicate entries in 57 lines? Regards, Rushi
View ArticleRe: SRX won't boot and won't start "loader.
I assume the SRX you pulled the USB snapshot from is the same model as the one that has difficulties. These instructions suggest a slightly different snapshot command you could try....
View ArticleRe: SRX 210 with Seirra Wireless USB 319u
Hi MarcTB ! Currently I have 01 USB3G Sierra 306. I have tried with following configuration (attach file)But interface cl-0/0/8 always in connecting state: show interfaces cl-0/0/8 extensive Physical...
View ArticleRe: srx340 as a switch and gateway router
I tested a similar configuration on a SRX340 last night running same software version and I cannot get it to work either. arp request/response does but no other traffic is showing up on the irb. I...
View ArticleRe: Gr-0/0/0 and st0 must have family inet address?
Hi Claire, # It is not necessary to provide a address on gre / st0 interface.unnumbered interface will work for you in both scenarios.GRE will have tunnel source and tunnel destination as the external...
View ArticleRe: srx340 as a switch and gateway router
did you guys do: set protocols l2-learning global-mode switch ?
View ArticleRe: srx340 as a switch and gateway router
I tried "set protocols l2-learning global-mode switch" and that worked. However, when I then configured the irb interfaces to use VRRP, the same issue occurred. I am not able to ping the virtual...
View ArticleSRX - No bootable media found
I have an SRX 220H. Whenever it reboots (i.e. power failure) it comes up to loader> Here is the bootup from console when I boot. The media must be fine because I can simply type "boot" at the...
View ArticleRe: SRX won't boot and won't start "loader.
The situation is critical - i have two clients with SRX100 with very similar problem during two days!!!Strange coincidence. I start to fear for other small branch SRX.First this SRX about which I was...
View ArticleRe: SRX won't boot and won't start "loader.
From your descriptions it does seem possible that your internal flash is failing on these devices. When a copy command like this stops at the same point consistently this tends to support the idea...
View ArticleRe: SRX - No bootable media found
This looks like your boot partition was corrupted in a power failure. You can use these instructions to reinstall Junos from this loader prompt....
View ArticleRe: Gr-0/0/0 and st0 must have family inet address?
Hi Hemant, Thanks!! (1) Yes, I have to run BGP on this tunnel. If for this I need to set gr-0/0/0 or st0 with family inet IP. Is this the same IP as the BGP router-id? For BGP over GRE over IPsec,...
View ArticleRe: Gr-0/0/0 and st0 must have family inet address?
Dear Claire I would suggest you use the same config strategy as the ISG. > Unnumbered for gr and st interfaces> Terminate VPN on lo0.0> Use lo0.2 for the BGP peering.> With BGP as the...
View ArticleSRX5800 --> Do i still need reboot to create address book IPv6?
Hi all, May i know whether i still need to reboot SRX5800 (flow mode) even i'm using firmware 15.x firmware on SRX5800? Thanks and aapreciate your feedback
View ArticleRe: SRX5800 --> Do i still need reboot to create address book IPv6?
Hello , We still need to reboot to enable IPV6 in SRX .
View ArticleRe: SRX5800 --> Do i still need reboot to create address book IPv6?
Hi joses, Thanks for your confirmation.
View ArticleRe: SRX5800 --> Do i still need reboot to create address book IPv6?
Hi Joses, Do i need to reboot both SRX (cluster) at same time or can do one by one? Thanks and appreciate your feedback
View ArticleRe: SRX650 Source NAT in HA Cluster : "dip alloc failed"
Thanks for your help. I opened a ticket. I think too that's a bug.Stay tuned...
View ArticleRe: SRX5800 --> Do i still need reboot to create address book IPv6?
Hello ,If you reboot them one by one , then one comes with IPV6 and other may be in IPV4 mode . This may cause unexpected behavior in cluster . Ideally there should not be any issue , but...
View ArticleRe: '${NODE}' is not defined
The configuration you specified under group node0 will be active only on node0 and the one you specified under group node1 will be active only on node1. Basically you have different active config on...
View Article