Quantcast
Channel: All SRX Services Gateway posts
Browsing all 17645 articles
Browse latest View live

Re: What do I need to VPN to a SRX100 from a laptop

Hi, You can refer the following link to configure dynamic VPN on the SRX :-http://www.juniper.net/documentation/en_US/junos12.1x44/topics/example/vpn-security-dynamic-example-configuring.html Hope that...

View Article


Re: SRX 3400 in Cluster config is synced but new configuration is not applying

Hi, The configuration sync happens over the control links. They seem to be up :- Control link status: Up Control interfaces: Index Interface Status 0 em0 Up 1 em1 Up I would suggest that you run the...

View Article


Re: SRX firewall routing configuration

show route command, one output lines i started to dig about shows as 681 10.14.224.193/32 *[Local/0] 24w6d 22:05:53 682 RejectYou get a reject local route when you have an ip address configured on an...

View Article

Re: Critical processes

From a monitoring perspective getting the overall cpu and memory should be sufficent for alarming.  The extensive view becomes the troubleshooting process during an issue. Also the most critical...

View Article

Re: SRX220 /jail/var over capacity

The place to start is to run the Junos clean up command request system storage cleanup

View Article


Re: SRX220 /jail/var over capacity

Hi Spuluka, Yep... Did that already, it was in my initial post.spuluka wrote:The place to start is to run the Junos clean up command request system storage cleanup 

View Article

Re: How to update Mini-PIM firmware???

 Thanks for the feedback Suraj. I found that page long before I posted the question. First of, the pic does not show up under "show system firmware" user@SRX210CM> show system firmwarePart Type Tag...

View Article

Re: SRX 3400 in Cluster config is synced but new configuration is not applying

Hi sahilsha thanks for your solution, yes hearbeats sent/received are incrementing previously this version was working fine for us but now it is not applying new configuration. We will ugrade its OS...

View Article


Re: SRX 3400 in Cluster config is synced but new configuration is not applying

Hi M.ali, You can check the links below for the methods of upgrading.1. ISSU...

View Article


Snmp v3 srx cluster, engine-id

From what i understand the juniper documentation is a bit contradicting regarding this: https://kb.juniper.net/InfoCenter/index?page=content&id=KB27191&actp=RSS here it says: "You must ensure...

View Article

Re: SRX220 /jail/var over capacity

du -ah /cf | sort -n -r | morewill show file sizes in human readible formremove big logsrm /var/log/httpd.logcopy it first off the box if you need itto avoid this in the future you can decrease log...

View Article

Re: SRX220 /jail/var over capacity

Hi, you httpd.log looks strangly big. Do you have any debugging (traceoptions) or syslog configuration for this file? On a test SRX httpd.log is only 8 kB - yours is over 1 GB! I would suggest you to...

View Article

Re: Snmp v3 srx cluster, engine-id

Hello, fisk4 wrote:  So whats really recommended?It depends :-)If Your SRX cluster is SNMP-polled via same IP (such as IP on loopback/lo0) and want Your SRX cluster to be represented in SNMP as one...

View Article


DIP configuration in Junos

I have the following DIP configuration in SSG and would like to configure this in Junos SRX 240. Can I get some tips on how to configure the following in Junos? set interface ethernet0/0 ext ip...

View Article

Re: DIP configuration in Junos

Hi, You can use the ScreenOS to Junos configuration tool for the translation. Try https://i2j.juniper.net/s2j/index.jsp Alternatively you can refer to the SRX NAT examples...

View Article


Re: SRX firewall routing configuration

thanks, when you descripe the interface as down, do you mean its down from the firewall configurations?or outside device, like router connected, and the interface from router side is down? any commands...

View Article

SRX 3600 chassis cluster cant configure IPv6 Static route with J-Web

Hi all, I'm configuring IPv6 Static route for Juniper SRX that installed chassis cluster. I can configure with CLI but cant with J-WEB (http or https). Pls see attachment.  Option for IPv6 is hidden. I...

View Article


configuring fxp0 interface for remote access

Hi all,i configured chassis in srx1500 firewalls.The management IP(fxp0) of node 0 is 172.16.10.1 and the management IP(fxp0) of node 1 is 172.16.10.2.. my problem is as under. 1) First i want to ping...

View Article

Re: configuring fxp0 interface for remote access

HI Asif, 1). You do not need to configure the FXP interfaces in any zones.2). You need to have system services ssh enabled on the devise.3). You need to have backup-router configured for the secondary...

View Article

Re: configuring fxp0 interface for remote access

Hi Asif, The Primary node uses its own routing table to respond to to-the-box packets and Secondary node uses something called a backup router (since routing is not running on Secondary).  On Primary...

View Article
Browsing all 17645 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>